Jump to content
SAU Community

Recommended Posts

what's your average fuel consumption and how do you normally use your car?

i was told my R33 GTS-4 would do about 11L/100km. i'll normally be using my car for short trips to the train station during weekdays (peak hour, so i can get to work in the city.. ughh...) and longer trips across melbourne over the weekend. do you think 11L/100km is a realistic average?

Link to comment
https://www.sau.com.au/forums/topic/187314-your-fuel-consumption/
Share on other sites

My GTR averages 15 to roughly 24L per 100, depends on the road :blink:

My supra around town is about 14L unless im being good with the throttle, but it uses next to nothing on the highway with constant throttle

My berlina uses 10L MAX around town, and basically runs on a drop when its on the highway

See the pattern? The more boring the car the less petrol it uses

low 11's / 100km. R34 GT-T, manual. full 3" stainless exhaust, manual boost controller. Tyres constantly at 38-40psi

But that's just burbs driving, mainly 60km/hr. So full city stop/start driving, 11.low/100

If i do some trips with some 100km/hr limits, i can get into the high 10's.

Never payed attention to how much my car takes but i've gotten almost 300km to a tank but usally arround 210-280 depending on how i drive and i've used up arround 1/4 of a tank hauling ass to work in 15 minutes or a little less, all i know is that i had to ease off a little 3/4 the way their because i saw the exaust temp light on (take that you sorry ass excuse for a turbo).

I'm not trying to brag, but one thing I always find puzzling about these fuel economy threads is that I get better fuel economy in my stagea than many people get in their skylines. Same engine, and more weight in the wagon (they're about 200-250kg heavier) and AWD and yet I'm getting 11-12L/100km driving to and from work (~30-45min drive). My car's not slow either (see my sig).

Obviously being in Adelaide the traffic isn't as heavy here but the difference shouldn't be more than 1-2L/100km at the most.

I would expect skylines to get less than 10L/100km or at least around 10-11L/100km in daily driving.

My stagea was doing 13-14L/100km when I bought it (stock) and with an exhaust, apexi SAFC, some ignition timing and a good tune, its now doing 2-2.5L/100km BETTER even though I'm running higher boost.

Hopefully you can improve your fuel economy too :D

I do very, very short trips (~5/6mins in the morning to work and same back home...could be three minutes if no traffic around...I could walk, but can't be bothered...it's cold in the morning anyway)

Around 14~18l/100km R33 GTS-T.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...