Jump to content
SAU Community

Tired Of Hearing About The Weight.


Recommended Posts

hahah not for you mate :banana: but we have done everything we can to take weight out of it, our budget doesnt stretch to carbon fibre so its running a fair bit of ally instead. I think you said you were building the 34 to sports sedan regs as well? so you know we have to retain factory floor pan. :angry:

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

yes best we could do was 1380, depending on fuel load, ( i needed to spend more money!) and that was enough :banana:

car came back from japan yesterday! ( thank god, fair bit of stress waiting for it)

cheers russ

need to send those bloody videos to you too

this isnt going to be popular but even the 32+ R's feel heavy to me around a corner... and yes once those tyres get really warm they do slide a bit easier.... the r's do seem to do it a bit quicker ... admitedly shithouse "sport" tyres ala kuhmo's dirty quantity evaluation.... but a benchmark none the less

spot on roy. the group A cars were heavier than my production race car (1530kg) so thats no excuse. And its also not true that gtrs get slower every lap, plenty of race times on natsoft.com.au including my races show otherwise.

i would be very interested to see how much weight the vspec can strip out.... I haven't seen 32-34 standard vs vspec or n1 but I bet the difference was less than 100kg, nothing like 200-300 kg different.

we have just stripped a shell really brtually for a new sports sedan, I will post up its weight once finished, but we are hoping for about 1250 - 300 kg less than stock

Improved Production R32GTR = 1280 kgs. All you need is money :)

Improved Production R32GTST (with RB30DET) target = 1130 kgs. All you need is time and a little bit of money :)

Cheers

Gary

I know of a guy in tassie who removed 200kg worth of unneccecary nuts and bolts from an s14. Weight reduction is easy!

Not possible, there is nowhere near 50kg of nuts and bolts in the whole car.

Edited by Adriano

lol. 200kg in bolts. I could take 200kg of bolts off my GTR but then I'd just be left with a partially assembled GTR and no way of ever putting it back together. and as Adriano suggested it's pretty unlikely even if you took every bolt out of the whole thing and held the car together with chewie and cable ties that you'd have 200kg in nuts and bolts.

I cant prove it and no doubt its an exaduration but im pretty sure it was only bolts he removed.

Cable ties were used.

Not possible, there is nowhere near 50kg of nuts and bolts in the whole car.

I disagree, nuts and bolts weigh alot.

Edited by ArBe20

I wasn going to say anything, but I've built a few cars in my time. If you took every nut bolts including the ones that is on the rods, head, crown pinion, harmonic balancer,clutch, flywheel and even wheel studs, you be lucky to get anywhere near 100kgs, and then you have to ask yourself the question would zip ties hold these "apparently" non essential bits together, as you just removed the primary method of attaching or fastening these items.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...