Jump to content
SAU Community

Recommended Posts

hey just thought id start the same thread as the one in NSW. I know its copying, lol but it seems like a good idea and a good way to network. And it gives a headsup to students at Uni or tafe and what they can expect in a particular industry.

Well im a second year Uni student, doing a double major in Accounting and Economics at Monash Berwick. Still not sure whether Accounting would be challenging or boring as everyone says lol. If there are any Accountants on here give me an insight in your typical day. Cheers

Link to comment
https://www.sau.com.au/forums/topic/217888-what-do-people-do-for-a-living/
Share on other sites

  • Replies 185
  • Created
  • Last Reply

Top Posters In This Topic

apprentice boilermaker, second year in a few weeks, dandy south location

a mate of mine is in his 3rd year studying to be an accountant, i have to explain to him shit about tax returns (usually after i ask him a tax question i end up explaining more than i learn) and i made him aware of the changes to the tax threshholds..... i hope your doing better than him lol

apprentice boilermaker, second year in a few weeks, dandy south location

a mate of mine is in his 3rd year studying to be an accountant, i have to explain to him shit about tax returns (usually after i ask him a tax question i end up explaining more than i learn) and i made him aware of the changes to the tax threshholds..... i hope your doing better than him lol

lol where bouts in dandy sth... hammond road? im in sth too. Im doing my Eco subjects this year and accounting ones next year, and im doing pretty good.. but yeh not everyone that goes to uni is smart.. i realised that this year. caus they could have gone to tafe, got people to do all their assignments and then transfer to uni.. but you cant do that at uni caus most subjects have exams with 70% of your total mark... anyway a bit of topic but jst an insight lol.

I sell fibre optic cable, accessories, rack cabinets, etc. Basically I sell anything to do with fibre optics (the data type, not the decorative lighting type.)

I started uni back in '03 and realised it was a waste of time for me so I got straight into work. I was always going to end up with a job in IT/Telecommunications.

Edited by llama_au
I sell fibre optic cable, accessories, rack cabinets, etc. Basically I sell anything to do with fibre optics (the data type, not the decorative lighting type.)

I started uni back in '03 and realised it was a waste of time for me so I got straight into work. I was always going to end up with a job in IT/Telecommunications.

my friend is currently studying telecommunications enigneering and needs to do Vacational work experience. Would your company be interested? PM us :ermm:

The networking has already begun!111 :whistling:

Im studying Industrial Engineering & Engineering Management at Monash Clayton.

Will be looking for vac work this year, so if any business looking for lean manufacturing, six sigma, performance rating etc send us a PM :blush:

Work for Tru Energy connecting gas and elec. Studied IT though but hard to get a job in that area. Worked full time as a comp tech before and do "backyard" jobs whenever I can. Just hard to get a decent paying job in the area. Studied Network Engineering.

I am an accountant and it isnt too boring but like any job it does have its moments.

I worked in tax for several years and it is the hardest and least paying area of the profession. Try to get into working for a big 4 firm in financial reporting or even auditing. THis will give you a good background to work for a larger company in commerce and away from public practice. Time sheets and shitty clients will bother you.

Working in commerce generally pays a lot more and is more rewarding IMO than public practice.

First few years out of uni suck but once you a qualified CPA or CA and gain a further 5 years plus experience you will not work for less than $100k.

I sell fibre optic cable, accessories, rack cabinets, etc. Basically I sell anything to do with fibre optics (the data type, not the decorative lighting type.)

I started uni back in '03 and realised it was a waste of time for me so I got straight into work. I was always going to end up with a job in IT/Telecommunications.

hopefully not selling fibre stuff for the pricks in croydon still!!

yes some of us are in IT

aswell as being part time spanner man / auto electircal conversion specialist.

im studying med @ monash (currently placed @ dande hosp). two and a half years ahead of me and 3 just gone. dont get paid anything for a looong time.

if i wanna get any decent pay, im also looking at another 4-10 yrs study postgrad. shoulda done IT

Bus driver for the State transit Authority...may not be the glitziest career, but its pretty relaxing and a fantastic perve as well...just think all those gorgeous city office girls I get to check out...of course the job has its moments ( like any job I guess )....but overall I enjoy what I do. No more manual labour for me again

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...