Jump to content
SAU Community

Recommended Posts

This might be of interest to those of you who like objective information; i've made a small table with some oil specs on it.

If anyone can find Motul specs PM me and i'll update the table. If anyone can tell me how to make an html table appear in a post, PM me. Pasting the HTML didnt work.

http://www.jaftan.com.au/skyline/engine/oilspecs.html

Rgs,

Kot

hey great information however there wasn't much talk about the VII content of wide spread multi-grades...i.e. as an eariler post by TREX01 stated good to keep the spread as close as possible i.e. 10w30 or 15w40...

are there any other opinions on this?

hey great information however there wasn't much talk about the VII content of wide spread multi-grades...i.e. as an eariler post by TREX01 stated good to keep the spread as close as possible i.e. 10w30 or 15w40...

are there any other opinions on this?

I do know that some oil like Redline 5w20, 5w30, 10w30 & 10w40 do not contain VII. The 5w40 may contain some or little VII.

Some Infor on VII and the shearing effect

Bobistheoilguy

I do know that some oil like Redline 5w20, 5w30, 10w30 & 10w40 do not contain VII. The 5w40 may contain some or little VII.

Some Infor on VII and the shearing effect

Bobistheoilguy

yeah I read that exact website after I posted it! however for other "full syns" which many are based on mineral base stock do...the HTHS rating should indicate the amount of VII addatives on wider spread oils I guess.

after reading al the stuff on the link it was quite intresting....worth a read if you want to understand oil ratings better. Most intresting were some of the comments about the cold start and operating temperature viscosity of of 10w30 Vs a 15w50 for example...

Edited by khunjeng

I USE Motul Turbolight 4100.

Have used many oils before and Motul is by far the best. My engine still idle's beautifully and the car runs smoothly as if its still new (its a 93 model) and its done well over 120 clicks now. As long as you put good quality oil and change it every 5000 clicks, it should be running like new. RB's are bullet proof if you dont do stupid mods.

Anyways Motul Oil is my choice Unless the engine is heavily modded and used as a Track car i cant understand why you would use any other oil!

and besides, its French hehe.

I USE Motul Turbolight 4100.

Have used many oils before and Motul is by far the best. My engine still idle's beautifully and the car runs smoothly as if its still new (its a 93 model) and its done well over 120 clicks now. As long as you put good quality oil and change it every 5000 clicks, it should be running like new. RB's are bullet proof if you dont do stupid mods.

Anyways Motul Oil is my choice Unless the engine is heavily modded and used as a Track car i cant understand why you would use any other oil!

and besides, its French hehe.

as there are no defined specifications (that I can find) for Motul I can't really see what the difference is between the Turbolight and the 300V series are. It appears the 300V range is promoted as thier "double ester" and assume it has a higher ester content than the Turbolight which may infact be a PAO base stock...

Motul are very lacking on their specs...intresting. By no doubt their oils are all good quality.

lol I sound like trex01 now...hehehe

as there are no defined specifications (that I can find) for Motul I can't really see what the difference is between the Turbolight and the 300V series are. It appears the 300V range is promoted as thier "double ester" and assume it has a higher ester content than the Turbolight which may infact be a PAO base stock...

Motul are very lacking on their specs...intresting. By no doubt their oils are all good quality.

lol I sound like trex01 now...hehehe

Do you guys have access to UOA kit? This will tell you the avg from the good.

khunjeng, Turbolight is just a semisynthetic. like GTX Magnatec etc. Nothing out of the ordinary about it really.

I suspected it was a PAO base stock...so yeah...I would not recomend its use over the 300V or other ester based products

Edited by khunjeng
check this oil out guys, $80 for 5 litres but seems to be worth it.

http://www.royalpurple.com/

Have seen some tests done on this and would like to get hold of some.

Can someone tell me where to buy Royal Purple Online?? I cant get it in my area?

check this oil out guys, $80 for 5 litres but seems to be worth it.

http://www.royalpurple.com/

dunno this product is a bit lacking on specific info regarding what base stock they use.

Edited by khunjeng
dunno this product is a bit lacking on specific info regarding what base stock they use.

They are using mainly 70-80% group IV PAO couple with 20-30% mineral additives carrier oil. They are pretty good but not quite a long drain oil. 10k is about max it can go.

HEY LADS,

I HAVE NARROWED MY OIL SELECTION DOWN TO 3:

MOBIL 1 5W/50

MOTUL 300V

MOTUL 8100 5W/40

my car is a 1994 R33 GTST, 126,000kms, manual.

which would be the best reccommended oil for my application.... up to now i have used MOBIL 1 but maybe its time for a change...

which is the best of these 3 for my car?

Also if i switch oils from Mobil 1 to Motul 300V or Motul 8100 5w/40 will i have to perform an engine flush to get rid of all remeins of Mobil 1?

any advice appreciated.

Beef

Edited by Beef

Geez this is an old thread good to see it revived.

We have conducted a heap of testing more recently again, testing in particular the SIn Penrite range and let me tell you don't overlook this stuff it shi.ts all over anything they have ever offered and competes better than some oild that were priced at double and tripple the SIN cost. Really recommend this oil its really good stuff!!

I USE Motul Turbolight 4100.

Have used many oils before and Motul is by far the best. My engine still idle's beautifully and the car runs smoothly as if its still new (its a 93 model) and its done well over 120 clicks now. As long as you put good quality oil and change it every 5000 clicks, it should be running like new. RB's are bullet proof if you dont do stupid mods.

Anyways Motul Oil is my choice Unless the engine is heavily modded and used as a Track car i cant understand why you would use any other oil!

and besides, its French hehe.

turbolight is a pretty average oil. that's why it's so cheap. it's a semi-synthetic oil. the 300V oils are 100%synthetic ester.

They are using mainly 70-80% group IV PAO couple with 20-30% mineral additives carrier oil. They are pretty good but not quite a long drain oil. 10k is about max it can go.

ok mate...yeah thats no so special really...not compared to the products we have been talking about.

Trex...one thing I'm not clear on is the group IV ratings...can u explain that a bit more...I'm pretty much down with everything else...type of PAO I assume.

ok mate...yeah thats no so special really...not compared to the products we have been talking about.

Trex...one thing I'm not clear on is the group IV ratings...can u explain that a bit more...I'm pretty much down with everything else...type of PAO I assume.

Ok, since you asked. Here are 2 link which talk more in depth into group I to V base stocks. :D

Base stock

Base stock 2

Edited by Trex101

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...