Jump to content
SAU Community

Recommended Posts

On a side note, I used a few tanks of E85 and just pulled my motor out and turbo off..

Both the inside of the manifold/turbo exhaust housing and turbine wheel are squeeky clean, amazing stuff! Almost looks like the car is running lean because there is zero soot after using the E42.5

downsides to the Ethanol's cleaning properties - where did all that crap wind up? Not that it all comes off at once of course :P

On an entirely related note (and this is going to make me look dumb) is an R33 GTS-T's fuel tank plastic or metal? Is there any materials inside the tank that can rust? It has been mentioned that if there is, filling it with ethanol would be a bad idea. All the shit in there gets cleaned out, then finds it's way through your pump and injectors, etc etc...

downsides to the Ethanol's cleaning properties - where did all that crap wind up? Not that it all comes off at once of course :P

On an entirely related note (and this is going to make me look dumb) is an R33 GTS-T's fuel tank plastic or metal? Is there any materials inside the tank that can rust? It has been mentioned that if there is, filling it with ethanol would be a bad idea. All the shit in there gets cleaned out, then finds it's way through your pump and injectors, etc etc...

Mine is metal, as long as they are galvanized the ethanol shouldn't react with the steel, 33's should be fine, not sure about the 32's.

You do run a fuel filter right?

Yes of course I run a filter - but no filter is perfect, not to mention just how quickly it could become clogged and restrict flow if huge shit is coming through.

So R33's are a plastic tank of some kind? Or are they galvanised steel? As long as there shouldn't be rust inside the tank, I'm happy.

Cats car has had a tank of ethanol sitting in it with the filler off and the pump cover removed (open to moisture for 3months) and there is no EVIL shit going on like is rumoured to happen.... i will leave it open to continue experiment :P

engine was internally mint (stripped to sell in parts) and exhaust etc is all fine.

Been running for over 18months now with no ill affects whatsoever. I too have left E85 in the tank for about 4-5months, no dramas.

I have a washable fuel filter and gets cleaned every service. The first 2 cleans had noticeable debris, after that it has been pretty clean.

Spoke to the attendant at Kambah earlier - he says within 2-3weeks they'll be pumping the good shit. They should have the equipment coming round this coming week to suck everything out of the existing E10 tank they'll be using, then clean it all out in preparation for filling with e85.

lolwut

That's retarded...when they WERE on the list, the servo had no idea what was going on...now that they're OFF the list, the servo expects it in the next couple of weeks.

hurr durr.

hahahahaa love it

Cats car has had a tank of ethanol sitting in it with the filler off and the pump cover removed (open to moisture for 3months) and there is no EVIL shit going on like is rumoured to happen.... i will leave it open to continue experiment :P

engine was internally mint (stripped to sell in parts) and exhaust etc is all fine.

can come one do a graph of injectors on E85

i.e

x6

555's = max power ____________ @ 45PSI or what ever std fuel pressure is

700's = max power ____________ @ 45PSI or what ever std fuel pressure is

1000's = max power ____________ @ 45PSI or what ever std fuel pressure is

thanks heaps

and am i right by thinking say 90PSI fuel pressure means 2x the cc?

Edited by yogibear

If you read this thread you will find there is quite a large difference in when people run out of injector duty cycle due to a myriad of different factors.

Remember a base fuel pressure is only a base. I think the standard base fuel pressure is 3 bar ~ 43psi, although it will raise 1psi for every 1psi of boost pressure. So if you are running 20psi of boost pressure then you are running 63psi of fuel pressure.

and am i right by thinking say 90PSI fuel pressure means 2x the cc?

no. double the pressure only yields ~40% more flow

skylines run a 3 bar fuel system standard, this means fuel pressure is always 3 bar (42-43psi) above inlet manifold pressure. this means theres a constant pressure difference between both sides of the injector (fuel on the rail side and air on the inlet side) resulting in constant injector flow.

  • Like 1

no. double the pressure only yields ~40% more flow

skylines run a 3 bar fuel system standard, this means fuel pressure is always 3 bar (42-43psi) above inlet manifold pressure. this means theres a constant pressure difference between both sides of the injector (fuel on the rail side and air on the inlet side) resulting in constant injector flow.

holy shit! someone who understands the basics of a fuel injected engines fuel system! well done. :)

most people have no idea. also no way is practical to take your standard 3 bar system and expect everything to be good at double the base pressure. 86psi base is going to cause some problems. first of which is most pumps will not be flowing anywhere near what they were at 3 bar under 6 bar...

if you are short on fuel supply by a small amount, 3 or 4% or something by all means use some more pressure. but anything more than that just buy the right size injectors and pumps. end of story.

  • Like 1

Just fueled up my 1st tank of E85 from Gosford caltex, i ran the tank extremely low so i would help reduce mixing of 98, then filled up @ 119.9 costing a total of $70 instead of $90 for 98,

from first start my idle went straight to 16.9 AFR from 14.3(98)

a quick change of injector size got the idle AFR back to normal,

Got my Fiance to cruise around while i touched up a few areas.

i used to get 400km to a full tank, ill see how this tank goes just cruising, then ill put a fresh batch in and strap it on the rollers,

without touching ignition timing the car feels more responsive, gave it a quick hit and it feels on par with 98, hoping to see some good gains once i tweak the timing.

current numbers on 98

293kw 18.5psi

255kw 14psi

  • Like 1

Roughly how much would I be looking at for a full retune onto E85? Obviously depends on where you go, and how good the tuner is....but for arguments sake, let's say Yavuz @ Unigroup...just wanna know if I can afford it just yet :P

Roughly how much would I be looking at for a full retune onto E85? Obviously depends on where you go, and how good the tuner is....but for arguments sake, let's say Yavuz @ Unigroup...just wanna know if I can afford it just yet :P

If you already have a full tune then a rutune on E85 wouldn't take too long...most tuners should be able to get in right in about 1-2 hours depending on how much time they spend on full and partial load maps and so on...of course this can change depending on what state the car is in and a whole load of other factors...so for your case...it depends on how much your tuner charges per hour...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...