Jump to content
SAU Community

Recommended Posts

just high flow it. not much more lag than std, and mines pushing 250rwhp at 1bar. thats got the afm maxed, the injectors are prob on the edge too being a red top. strangely the std fuel pump still has some left, unless it was modified in jp. can be done for around 1k or another option is the rb25 unit with similar results but ceramic exh so itll be on the limit

A HKS2530 will give you "Plenty of performance" - around 210-230rwks

Beyond that it cost substantial $$$. What $$$ are you realistically looking at spending on just turbo???

I would love to see what a properly setup HKS2835 with manifold/wastegate/ECU/injectors/AFM would do on an RB20.

A Trust TD06L2-20G-8cm kit with manifold/wastegate is about as big as id go, any bigger and boost response may be compromised a little too much. (Lag in negligible, with boost response bumped up about 1200-1500rpm)

  • 9 years later...

wat's the best turbo for the rb20det, without too much lag, fuel cut etc. and with plenty of performance??????? :burnout:

n e ideas or info wuld b much appreciated

a garrett 2871r would be in the range, a 0.63 rear housing and cranked up to 18-20psi with possibly some E85 to make it come alive even more..

there common on sr20's from what ive seen/read.

How much power are you aiming for?

They have nothing before 4 grand anyway just get a TD06L2 20G 8cm (like $799 from the kando or a billet one from hypergear), a few people have said they have moved from something like a 2530 to something larger and not noticed much difference.

But it depends what you want if you want a whole highmount setup or if you want to keep it as stock looking as possible etc etc.

You mentioned fuel cut. There's no point upgrading the ECU if you're not going to remap or Nistune the ECU at least. I'd go a Garrett GTX3067R with an ATP divided .82 housing on stock manifold modded for external gate.

That would be quite disgusting to drive until 6000. Divided housing then put it on a stock manifold, not really that helpful there

Divided housing then put it on a stock manifold, not really that helpful there

I'm assuming RB20 manifolds are the same as RB25 ones and are divided (other than the 5mm gap which can be welded up)? Why would it be disgusting until 6000? Stock manifold will have better response than aftermarket. I am referring to the new smaller GTX3067R, not a typo of a GTX3076R. The divided .82 housing has better response than an open .63. This setup would be more responsive than a GT-RS/GT2871R with the right tuning and cam gears with a fair bit more top-end potential. Why would this be discusting until 6000? Disgusting on tyres I guess haha. Edited by bradsm87

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
    • I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
×
×
  • Create New...