Jump to content
SAU Community

Recommended Posts

I already said the comparison is pointless unless we use the same dyno with same car. I didn't make any of those sheets either.

To get 200rwkws with 3076 .82 by 4000RPMs that is possible with race fuel and cam gears which you can add heaps of timing down low. But I haven't seen any one made that with all stock parts.

Or use a 71mm comp wheel with cam gears. But I think its hard to crack 300rwkws with 98 fuel.

I can't find any that come even close to 200rwkw at 4000rpm... Care to point me in the right direction?!?

See this is a baby 52T ATR43g2 high flow in .63 rear with cam gear and 98 fuel. Its pretty close to 200rwkws by 4000RPMs. But Its going to be maxed around 270rwkws ish. If you run Race fuel in that you will get more then 200rwkws by 4000RPMs maxing out at 300rwkws.

253rwkwsop6highflow.JPG

No race fuels, no cams. They do it.

I dont wish to debate the garrett vs your turbo, I just wanted to point out it was a poor comparison.

One further thing you may want to consider is how long the curve stays concave. The above graphs show the 3076 has a far more convex curve. This would be highly appealing to many people looking for as much area under the curve as possible.

SimonR32, majority of results I found were on this site, search and yee will find. It has been some 6 months again, I since purchased a 3037 (and ironically am now selling it) and havent looked since.

For once more I've said the comparison is pointless unless certain conditions are met (which is not), and I'm not the person who posted them or responsible for their actions.

I've seen Simon-R32's results. How ever that is running off .63 rear housing with a 44mm external gate alone with all other mods. If I do all those to my test car then I can also get his result. He's not running 98 fuel either.

After reading through his thread and understood what he've gone though for his result would you just bolton a 3076 in .63 int gated rear to your factory setup and hopping for 300rwkws with pump fuel?

How ever my goal is building a solid bolton turbo that can produce such power with less as possible modifications done to the factory package.

If I modify my car to the stage as his and selling my services to others based on that result, I call that fraud. I'm not trying to modify my setup to bring out the best out of a turbo, but trying to build a turbo to bring out the best of a "stock setup".

To me GT3076 in .63 rear internally gated can not make a genuine 300rwkws with fully stock setup and 98 fuel. From my experiment It will drop lot of boost with standard actuator, replace it with a high pressure valve and gate controller, it creepes so much heat that turned it self red hot and you lose power after every run.

SimonR32, majority of results I found were on this site, search and yee will find. It has been some 6 months again, I since purchased a 3037 (and ironically am now selling it) and havent looked since.

Look again, I think your memory has failed you :)

Look again, I think your memory has failed you :banana:

I agree, I cant see any 3076s (0.82 housing) that make 200rwkw at 4,000rpm on 98 fuel.

I can see a few HKS 2835 Pro S setups that make 200rwkw at 4,000rpm but even they need E85 fuel for that.

The target is 100-120 KPH as most graphs are in speed rather than RPM.

With different ratios or wheel sizes this is an approximate marker for the 4000RPM range in 4th gear.

I remember feeling entirely the same, all the 3076 rage rah rah rah, smaller turbos are far stronger down low etc etc. Some better investigation brought that 200kw marker to light.

The graph above for the 52T is showing 200KW @ 4200RPM at 17psi, look at how much earlier the boost comes in too, the 56T would easily exceed that at that point. Its on full boost by 3450RPM, do you really think the 56T will be 1000RPM laggier, no. But it will flow a considerable amount more at that point.

Flow = power, direct relationship. < thats a full stop.

The target is 100-120 KPH as most graphs are in speed rather than RPM.

With different ratios or wheel sizes this is an approximate marker for the 4000RPM range in 4th gear.

I remember feeling entirely the same, all the 3076 rage rah rah rah, smaller turbos are far stronger down low etc etc. Some better investigation brought that 200kw marker to light.

The graph above for the 52T is showing 200KW @ 4200RPM at 17psi, look at how much earlier the boost comes in too, the 56T would easily exceed that at that point. Its on full boost by 3450RPM, do you really think the 56T will be 1000RPM laggier, no. But it will flow a considerable amount more at that point.

Flow = power, direct relationship. < thats a full stop.

So the turbo above doesnt even meet your requirement of 200rwkw @ 4000rpm but your saying a larger turbo (56T) will?

Surely with the number of them out there a real life example would be available if it was such an easy thing.

The target is 100-120 KPH as most graphs are in speed rather than RPM.

With different ratios or wheel sizes this is an approximate marker for the 4000RPM range in 4th gear.

I remember feeling entirely the same, all the 3076 rage rah rah rah, smaller turbos are far stronger down low etc etc. Some better investigation brought that 200kw marker to light.

The graph above for the 52T is showing 200KW @ 4200RPM at 17psi, look at how much earlier the boost comes in too, the 56T would easily exceed that at that point. Its on full boost by 3450RPM, do you really think the 56T will be 1000RPM laggier, no. But it will flow a considerable amount more at that point.

Flow = power, direct relationship. < thats a full stop.

Using wheels speed is inaccurate unless you know diff ratios, wheel/tyres sizes etc. and this is why you are being misguided!

The 56T is a 0.84 rear and 52T is a 0.63 rear, so a bigger compressor and bigger exhaust housing would make for about 700-1000rpm laggier yes!

Edited by SimonR32
Using wheels speed is inaccurate unless you know diff ratios, wheel/tyres sizes etc. and this is why you are being misguided!

The 56T is a 0.84 rear and 52T is a 0.63 rear, so a bigger compressor and bigger exhaust housing would make for about 700-1000rpm laggier yes!

Which is why I have not made point to be exact.

It has also been documented that there are gains to be had in the larger housing over the smaller one. The added volume aids in lower combustion temperatures and more timing can be wound into the motor.

One correction to my 'claim' that has shed many a tear it seems, results were more consistent when using an exhaust cam gear.

You are comparing Dyno Dynamics readings with a Dynapack reading - it can't really be done.

yes it can.... Dynapak has a correction mode that will give it DD readings to within a kw or 2 :banana:

a well tuned RB25 with a 3076 should achieve close to the 200rwkw mark by roughly 4000RPM. I am talking about an internally standard motor, no cams.

on pulp... a 3071/2835 will just make it... but only if you reeeealy push it

fwiw...

this is my car: tuned on the same dyno (trent @ status)

unopened RB25 with an HKS 2835 pro s, (3071 w HKS spec .68 rear). I am running a greddy rb26 ex cam gear, hybrid GT intercooler, stock throttle body, plenum etc

the red line is BP ultimate and the blue line is manildra e85

@ 4000 rpm pulp makes 190rwkw and e85 makes 210rwkw

gallery_36777_3194_124976.jpg

Larger the trim is the more vertical power behavior you get. To get a smooth build up of power you need to run a large comp housing with a small trimmed mid size comp wheel.

I wouldn't call the smoother the better. turbos do produce this vertical power increasement has a very sharp and strong punch on acceleration. while the build up turbo would give a lot smoother sort of feel.

But if you are dragging, The car that reaches peek power and torque quicker is more likely to win.

We can build them to do either, so I would say it depends on people's preferred driving ability.

I think your above power curve of the ProS is similar to this one here:

atr43G363295rwkw.jpg

Its a customized GT30 wheel running on stock cams and 98 fuel. That would be the most responsive towards 300rwkws as you can get. Car wasn't strapped down, had plenty wheel spin.

Wow! Full boost before 2500 and 250 killerwasps!

Dragon eggs for sure.

Yes Stao I do agree the concave curve would feel faster, although I disagree that it is likely to win. I would say it is fair to say it would have more traction issues for the same final output :banana:

Only issue with that last dyno plot tao is the power falls over after 5,600rpm. I wonder how far it would fall if you kept going till 7,000rpm?

But yes its quite responsive, very impressive. Hard to have everything I suppose.

that's true... the 2835 is still going strong by my 7400rpm limit (not on that particular 6800 graph, just take my word lol)

unopened RB25 with an HKS 2835 pro s, (3071 w HKS spec .68 rear).

Is the exhaust housing the the only difference between the HKS 2835 pro s and the Garrett 3071?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...