Jump to content
SAU Community

Recommended Posts

hahahaha my suggestion was in no way serious :) I'd hate to think what kind of distorted readings the AFM would get when placed directly in front of the turbo inlet anyway.

So does anyone make an alloy one with bov/breather return that isn't $300 ?

Does anyone make an alloy one with bov/breather return that is good? I didnt know there were any at all, at any cost.

I just made one up myself... Just get a 3" 90 deg bend and weld on a few plugs then use radiator hose to connect between original return pipe and the custom intake

Thats exactly what i did. $10 scrap exhaust bend from an exahust shop. cut the bov return and oil breather metal return pipes off (about 30mm cut off) turned them around and welded them onto the exhaust bend, then 2 small hoses (about 80mm) long to join up the now cut bov return and oil breather.

Chasers made mine because, as other people have found, the rev210 mod does have it's limits. 2 x 45 degree bends were used in the end i think, they wanted it as straight as possible.

They did say it was tricky to get it to work, which must be what all of you guys are talking about.

I have the standard airbox and standard BOV, plum-backed.

Wasn't cheap, $300+, but still let me run everything as it was and in it's most standard configuration, whilst being the straightest possible pipe.

that should all be past tense, as i no longer have the car :)

Chasers made mine because, as other people have found, the rev210 mod does have it's limits. 2 x 45 degree bends were used in the end i think, they wanted it as straight as possible.

They did say it was tricky to get it to work, which must be what all of you guys are talking about.

I have the standard airbox and standard BOV, plum-backed.

Wasn't cheap, $300+, but still let me run everything as it was and in it's most standard configuration, whilst being the straightest possible pipe.

that should all be past tense, as i no longer have the car :)

Thats the next level of complexity again as you have to connect it up to the standard airbox. I am just talking about a pod filter so it doesnt have to be as precise.

I made THIS for the same reasons as above.

All you need is some alloy pipes and a welder.

I made this one 2.5" on the turbo end and 3" on the AFM end so no need for silicone reducers (ugly)

I made THIS for the same reasons as above.

All you need is some alloy pipes and a welder.

I made this one 2.5" on the turbo end and 3" on the AFM end so no need for silicone reducers (ugly)

Good to see another way of doing it!

However, for the guys with larger turbos I am sure it would be beneficial to go straight to 3" as quickly as possible from the turbo. I know its the not exactly the same but its sort of like a bellmouth if it goes straight to the largest diameter. Thats my theory anyway.

Had car retuned today after I had a few issues fixed up...I'll be providing Stao with the dyno sheet to post up first once I pick the car up, but all I can say is that I'm very happy with the figure. Considering I asked the tuner to be as conservative as he could and very safe up top, it still made stupid power. He was skeptical of the turbo since he'd never heard of them before, but was pleasantly surprised (or astounded moreso) with the power it made.

Since it was running without any boost control, boost came up to ~17psi initially and bled down to ~15.9psi. Tuner took out as much timing up top as he could before it would begin having a negative affect, and it finished up with 11.5AFR. Not sure of the rpm yet, but at 15.9psi it made 294rwkw.

Safe to say I'm stoked with this result.

Thats awesome, can't wait to see the dyno graph.

Mine's going back on the dyno on monday too! last tank of fuel before i switch to E85 :D

You're a prick. I want some ethanol action :no:

Who's tuning it for Ethanol?

Had car retuned today after I had a few issues fixed up...I'll be providing Stao with the dyno sheet to post up first once I pick the car up, but all I can say is that I'm very happy with the figure. Considering I asked the tuner to be as conservative as he could and very safe up top, it still made stupid power. He was skeptical of the turbo since he'd never heard of them before, but was pleasantly surprised (or astounded moreso) with the power it made.

Since it was running without any boost control, boost came up to ~17psi initially and bled down to ~15.9psi. Tuner took out as much timing up top as he could before it would begin having a negative affect, and it finished up with 11.5AFR. Not sure of the rpm yet, but at 15.9psi it made 294rwkw.

Safe to say I'm stoked with this result.

Sounds good! Keen to see your boost graph so don't forget to get a print out while you are there :no:

Also try and get the runs printed in rpm if you can

Not sure mate. I'll go back to Ed on monday to get a "before" and base tune.

Then I'll tune the AFR's myself and up the timing a bit. Then bepending on how Ed goes with the before tune i might go back to him.

Otherwise i dunno

As some already seen the ceramic ball bearing high flow results. This is based on a stock Rb25det with factory head, cams and cam gears with forged bottom. Turbo did have some unexpected boost creep issues due to a newer designed waste gating system.

Tuning video footage of 4x consecutive runs. with consistent 321rwkws:

op6highflow321rwkw.jpg

op6highflow321rwkw2.jpg

op6highflow321rwkwboost.jpg

Turbo has been pulled apart, we are analyzing its bearing components and modifying its turbine wheel refer to some skeptics for faster torque gain.

Also we will be testing some cage less air craft ceramic bearings for even faster spool time.

post-27032-1287745479_thumb.jpg

Also for people whom's interested in sleeving stock rubber pipe with metal and hopping for great HP. Below is a dyno comparison to show you it doesn't work. and please don't waste time trying. (The drop at 6500RPMs was from operator back off per discussion earlier)

puvsrick.jpg

I would highly recommend going fora 4inch metal intake pipe with pod. All ATR43G3/4 units will be now built with a .70 comp housing with a 4inch inlet unless special request.

Since I got no idea if Stao is gonna chuck these up or not, here's the dyno charts from my tune this arvo. I don't get a torque chart tho :ermm:

One shows power+boost, one shows power+AFR. They've been overlayed onto the graph from my first tune when I was having boost issues. The RED line is from today (though I dare say that will be obvious lol)

post-60560-1287746563_thumb.jpg

post-60560-1287746602_thumb.jpg

Big thanks again to Stao and his great work, another happy customer here :)

Thanks for uploading. I was about to re-size them first. Unfortunately above turbo had some shipping damaged to the actuator lever which caused it not been able to shut in the earlier run. Great to see thing's back in working order. Hopping to see more power at 20psi :ermm:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...