Jump to content
SAU Community

Recommended Posts

Ok I've now fixed my air leak (loose hose clamp), changed exhaust and removed the boost control. Still getting 22psi dropping to 14psi by redline. Stao can you send me a stronger actuator to try.

Ok I've now fixed my air leak (loose hose clamp), changed exhaust and removed the boost control. Still getting 22psi dropping to 14psi by redline. Stao can you send me a stronger actuator to try.

Was that with the air box lid and filter off?

I couldn't suggest running without a filter. I had a 1mm gap between the gasket in my apexi filter and z32 and enough shit got in to damage the turbo fins. Silly idea. At least put a stocking over the box snuggly so at least you know some shit wont go in.

One run down the street should be fine surely? Just don't drive through gravel or anything like that. I'd be more worried about the sock getting eaten.

Edited by Rolls

So has anyone got their SS1PU fully tuned with dyno results yet?

I got mine in the mail yesterday, should be fitting it this week.

Yeah, 260rwkw on 19psi, stock internals. Dyno vid is on youtube :)

xxswitchfloxx

Mods are on there also. I might have a dyno pic lying around too ill post up in a sec

dynograph.th.jpg

Yeah, 260rwkw on 19psi, stock internals. Dyno vid is on youtube :)

xxswitchfloxx

Mods are on there also. I might have a dyno pic lying around too ill post up in a sec

Thanks mate - dyno would be awesome, esp with the boost. Does it hold 19psi all the way or run more/less in the midrange/top end?

Whats it like to drive?

19psi at like 3500-3700+ rpm, then dies down to 17psi by redline.

Stao mentioned i use the screws that came with it to stop the boost dropping, some sort of airflow changing method. Not sure how it works, but seeing as its a pain in the arse to get the turbo off theres no way i have the time to take it off continuously to see how far each screw needs to be turned for the boost to stay level. Not to mention the time it takes for the turbo to cool down enough to touch..

Very fun to drive, not the best top end acceleration but that's not what i wanted. This is my daily driver, so i wanted low end power and that's what i got.

Spinning wheels in first and second and get sucked in the seat :)

Keep in mind, those results were after a lot of runs, so heat-soak set in. I reckon on a cold day + first try it would make over 260.

Has anyone been in a car with a atr43 g3 and atr43 ss1. I'm considering upgrading from the ss1 to the g3 and just wanted to know what people think of the difference.

Do you need to upgrade or do you need to work out your issue?

IIRC your already making the projected power for the SS1 though arent you? Being 240kwasps

It's just a possible solution to the boost drop, stao has suggested the upgrade or a bigger actuator. But I'm deffinately not happy with the power but i don't think that it is the turbo. My tune is all over the place.

Edited by lilcrash

Do u have a dyno graph lilcrash?

I have done a g3 on a 34 but maxed the stock injectors at 232kw 19psi 6000rpm

And dynafits ss1.5 259kw 19psi with weak clutch

Has anyone been in a car with a atr43 g3 and atr43 ss1. I'm considering upgrading from the ss1 to the g3 and just wanted to know what people think of the difference.

I have had both on my car with exactly the same mods. They are completely opposite turbos. The ATR43G3 was over 1000rpm less responsive then the SS1, was a HUGE difference. I was able to make 280rwkw with the ATR43G3 and 245rwkw with the SS1. The SS1 is way better for the street, standard turbo like response. I now use E85 fuel and make 280rwkw with the awesome response.

On both turbos my boost would drop to 15.5psi no matter what I did, boost controller, wastegate studs etc. I found replacing my intercooler and fixing up the exhaust helped as now boost only drops to 17.5psi. So for me it was other restrictions in the setup that were holding back the boost up top.

If you wanted to go bigger I would stick with the SS range, either the SS1PU or the SS2. I thought the ATR43G3 was too laggy for a street rb25. The SS2 is around 3-500rpm more responsive then the ATR43G3.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...