Jump to content
SAU Community

Recommended Posts

hi hypergear mate. just a suggestion for ya, dunno if you agree. when you post up your turbos i rekn u shud put the price of it up aswell next to the model code. i always go on there and see them and im like ooh i wonder how much that one is. dont wanna pm you about every one i see every new day or whatever

Have you thought about how youre going to get home, because it's 400 odd kms and I don't think you will make it on one tank of e85. Is there a servo on the highway that sells it?

Might have to carry a few jerry cans with you?

I was going to try for a dual map setup.

Just use a laptop to switch between 85 and pump

So get it tuned with Jez and then drive home on 98?

I dont know how easy this will be or not

The only issue with dual maps is while the transition between fuels is happening there may be some residual fuel left which can affect the tune till it is all out. Aslong as u dont drive hard during the transition

I was going to try for a dual map setup.

Just use a laptop to switch between 85 and pump

So get it tuned with Jez and then drive home on 98?

I dont know how easy this will be or not

Oh ok, it'd probably be a bit of a sl*t initially when you change maps but I can't see why it wouldn't work. You will probably end up on 98 most of the time because there's limited access to eflex in Canberra.

Probably best to chat with Jez about it and see what he thinks.

Edit: Jez just posted in here

Edited by Mitcho_7

The only issue with dual maps is while the transition between fuels is happening there may be some residual fuel left which can affect the tune till it is all out. Aslong as u dont drive hard during the transition

Is there any way around this?

Such as what stao said where he has the pickup right in the bottom of the tank.

I cant afford to run 85 all the time and I can no way afford a flex setup haha

Is there any way around this?

Such as what stao said where he has the pickup right in the bottom of the tank.

I cant afford to run 85 all the time and I can no way afford a flex setup haha

85 is cheaper per litre but it contains less energy, so it probably work out the same as 98 cost wise/distance travelled.

I think if you're going e85 commit and run it all the time or theres no point really.

Then have the 98 map as a backup if you are caught somewhere that doesn't have it

Edited by Mitcho_7

Yeah thats what would be happening.

I would be using the girlfriends car when traveling to the coast etc.

Just need it as a back up if I get stuck.

**Stao when you get in here mate let me know if you have ever put the SS1PU on 85 or if its going to happen.

Would love to see results

I agree, you will end up never going back to 98 anyway once you have felt the powerz. You can feel good everytime you get on the gas too, its green fuel, carbon neutral so your'e doing the planet a favour dropping that skid. :)

I thought about that mitch but I just cant get my head around the costs of it.

Probably should sit down and work out everything.

See which is most cost effective

Wmi will probably work out more long term. The cost of the kit is comparable to injectors etc so that's negligible.

Its Mostly due to the fact that the price of 98 will get higher because it's dictated by the cost of oil which we don't have much (if any) supply of our own, so we are at the mercy of OPEC and the us dollar cross rate. You also have to get methanol ($80 for 20l). Whereas e85 should be a steadier cost because it's made from things we have an abundance of on shore.

Edited by Mitcho_7

Fark cheaper then the SS1PU

SS1PU is the response king though, still loving 3rd gear at legal speeds :)

Is there any way around this?

Such as what stao said where he has the pickup right in the bottom of the tank.

I cant afford to run 85 all the time and I can no way afford a flex setup haha

If you have 1-2 litres of E85 in the bottom of the tank and you fill with 60 litres of 98, as long as your 98 tune isn't on a knife edge, it's not going to die in the ass. Better yet, get an emergency tune made up, based on a couple of litres of E85 being left in the tank and then filled up with 98...

E content sensor will be handy too.

Maybe just get Jez to tune both maps with 5 or so litres of the other fuel in the tank?

Yeah this would be good.

And as Birds said make sure its not knife edge which I know Jez doesnt tune like this.

SS1PU is the response king though, still loving 3rd gear at legal speeds :)

This is very true but 2nd gear is snapping into 3rd is my fav!

It steps out out when ever you plant it in 2nd.

Have you fixed your clutch slip?

Whereas e85 should be a steadier cost because it's made from things we have an abundance of on shore.

Scotty would have a better idea about this than me but it seems like E85 pricing goes up and down in conjunction with regular petrol pricing. If 98pulp goes to $2 I highly doubt E85 will still be under $1.20 or even $1.50...

Caltex is 20c less than unleaded. United were 10c less, but they just dropped 15c off the price so 25c less than unleaded. They both have ethanol plants in Queensland now but I'm not sure the Caltex one is operational.

The price is set against oil for some reason, sounded dodgy as hell. I have the email from Caltex about it and I posted it in the E85 thread a year or two ago.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...