Jump to content
SAU Community

Recommended Posts

You got da high comp bro and you worried about response?

I don't see any other option for you... You can deny it as much as you want but I can see you filling at caltex within the year. lol.

lol when caltex roll it out across the state ill be using it for sure. at the moment theres nothing local to me which supplies it.

if the car ran out of fuel its like hey lets go for a half hour drive with a jerry can lol about half an hour in only 2 directions. much further in any other :(

the high comp is due to retire soon. DET block has been bored 20thou and CP pistons at 8.5:1 have been match bored already. crank is next (once i pay for some dental), will match some bearings to it and check the rods. put it back together shortly after and grabing a 20g to go.

plan is to pick up some detchwerks 1000ccs while im at it so im ready for the good stuff when its actually available ;) keep in mind my car is intended as a frequent driver and track car. the only ameture friendly track is over 2 hours drive away and i havent seen a caltex there let alone any eflex supply lol. but sooner or later ill join you guys on that bandwagon, yes.

This is very true but 2nd gear is snapping into 3rd is my fav!

It steps out out when ever you plant it in 2nd.

Have you fixed your clutch slip?

My tyres hold strong in 2nd, it's the clutch that let's go when the power comes on! Meant to have clutch in the other day...but we had a customer warranty job to fix, so my car should be on the hoist tomorrow hopefully!

S1 R33

3 inch dump,high flow cat, 3 inch exhaust

Apexi metal intake pipe with pod --- problem?

China fmic --- problem?

044 fuel pump

660cc high flow injectors

Superspark coils with copper plugs @.8

Nistune ecu

Eboost street

SS1pu

277.0hp @17psi

There isn't any boost leaks, we checked while there. I also double clamped all the pipes to make doubly sure.

I did check at the time whether i pulled all the rags out as well.

It's got me stumped, any ideas??

Encouraging news.

Replaced the cat with a 100cell 5inch body metal cat (forget the brand,venom?)

Plazmaman FMIC with a turbosmart fully recirc BOV

3 inch metal intake (thanks to Scotty)

I put a nistune map on that Stao gave me and it's boost waaaaay earlier, only put the map on for a trial. It coughs its guts up any higher than 3000rpm but i did see 10psi at quarter to half throttle by then.

I've put the Hyperdrive map back on until i get it to the dyno again.

Next problem is, do i take it back to Hyperdrive or Pzp? or even post it off to Toshi?

Wish i could take it over East, sounds like theres some great tuners over there.

Anyone know of anyone else in Perth that tunes r33 with z32 ecu?

Cheers

Encouraging news.

Replaced the cat with a 100cell 5inch body metal cat (forget the brand,venom?)

Plazmaman FMIC with a turbosmart fully recirc BOV

3 inch metal intake (thanks to Scotty)

I put a nistune map on that Stao gave me and it's boost waaaaay earlier, only put the map on for a trial. It coughs its guts up any higher than 3000rpm but i did see 10psi at quarter to half throttle by then.

I've put the Hyperdrive map back on until i get it to the dyno again.

Next problem is, do i take it back to Hyperdrive or Pzp? or even post it off to Toshi?

Wish i could take it over East, sounds like theres some great tuners over there.

Anyone know of anyone else in Perth that tunes r33 with z32 ecu?

Cheers

Preferably Allstar in WA, Just get them do a check up and some patch up if required.

So this is what happens after 400-500 launches, several DECA/skidpan days and 3 years of daily driving. It is was a cushion button, so there's supposed to be organic lining between them fancy paddles...which have about half a mm left in them. Note also the heat spots on the cover plate. All in all a solid effort from the Exedy, as she was still letting me launch hard until the very end, only giving out under too much boost (SS1PU POWAAA) and I think that was clamping pressure related. Would definitely use this clutch again if I wasn't making too much power for it.

Waiting for my flywheel (read: saucepan) to come back from being machined and then the NPC organic + reco gearbox go in. <2 hours work so far, not bad for a gearbox and clutch change.

8b+YM_E2_original.png

YeMcYm+V_original.png

So this is what happens after 400-500 launches, several DECA/skidpan days and 3 years of daily driving. It is was a cushion button, so there's supposed to be organic lining between them fancy paddles...which have about half a mm left in them. Note also the heat spots on the cover plate. All in all a solid effort from the Exedy, as she was still letting me launch hard until the very end, only giving out under too much boost (SS1PU POWAAA) and I think that was clamping pressure related. Would definitely use this clutch again if I wasn't making too much power for it.

Waiting for my flywheel (read: saucepan) to come back from being machined and then the NPC organic + reco gearbox go in. <2 hours work so far, not bad for a gearbox and clutch change.

I raise you my button clutch, I did this just daily driving the thing ; ) Totally destroyed it, you can see the heat discolouration and warping of the rivets, with only 150rwkw as well lol.

clutch1w.jpg

Edited by Rolls

You know, you're not supposed to be proud of destroying it that easily :P

Was yours cushion button or button? Looks to have the buttons of a cushion, but your sprung centre is different to mine?

You know, you're not supposed to be proud of destroying it that easily :P

Was yours cushion button or button? Looks to have the buttons of a cushion, but your sprung centre is different to mine?

cushion apparently, but it was TERRIBLE to drive, shuddered and f**ked my gearbox, in the end it still had massive bite and shudder but would slip on hard changes to 2nd.

I am renowned for having no mechanical sympathy haha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...