Jump to content
SAU Community

Recommended Posts

I'll be be keen on seeing results for the td06sl2 int gate billet wheel as Im intrested in one but the kando ones have boost creep issues cause the wastegate hole is too small so hopefully this one outperforms it

Will you have them in t2 aswell ?

T518 style T28 internally gated patterned turbine castings are available. re-make another wastegate port and disc isn't much of a problem. How ever those turbos don't perform an where near to what they do externally gated mainly due to its turbine wheel and housing design.

I think there would be some money to be made if you could make a decent rb bolt on td turbine housing. Seems everything out there is pretty crap

Our current ATR28xx and ATR43xx Rb25det and SR20det internally gated bolton options are pretty mature, they would out perform most of TDxx turbochargers internally gated (and some externally gated). No point going over what ever already done. Do check them out for a bolton internally gated option.

Our Billet TDxx series will be engineered for externally gated purposes.

All turbochargers will be made to order in strict time bases, great support and customer services as always, and we won't be blocking any one on ebay.

Haha thems fighting words. Good work Stao!!

Stao, the nipple that goes in the top of Ss2 cartridge, do you just use a bit of thread sealant on it? The nipple looks like its supposed to have an o-ring on it but the chra is threaded right to the top with no recess for an o-ring. After a drive the top of the chra is damp with oil. Must be loosing 2-3mL each drive.

Putting loctite thread sealant on it now and will test drive again after lunch

Cool that's what I ended up doing earlier on. Just finishing oil pressure sender fault then I'll degrease it and go for a drive.

3 sleeps til it's tuned

Gahh im so impatient!!

How long did it take for people in perth to recieve there kit from over east ?

Its only been 8 Business days but it feels like a eternity!!!!

Looking forward to what it can do with my 34gtt :)

7-9 consecutive days. Mine has been over n back n over

My SS2 goes on dyno in the morning. Unfortunately the exhaust isn't as free flowing as I would like with a cheap Catco Cat on it. Will change it when I get back from Japan next month

7-9 consecutive days. Mine has been over n back n over

My SS2 goes on dyno in the morning. Unfortunately the exhaust isn't as free flowing as I would like with a cheap Catco Cat on it. Will change it when I get back from Japan next month

What mods? Int or ext gate? 98 or 85?

I've already bought my ss2 int gate but won't be putting it on till next month

So a little eager to see someone elses result!

What mods? Int or ext gate? 98 or 85?

I've already bought my ss2 int gate but won't be putting it on till next month

So a little eager to see someone elses result!

In gate, standard manifold port matched n opened up. 98ron. Poncams, port n polish, head chambers decompressed, power FC with nismo 740's,z32,3inch scotty intake,bell mouth dump to cheap cat to single muffler. Hypertwin. Freshly rebuilt engine

Edited by t_revz

Maybe just for the tune get a straight through?

You dont want to have factor in there that will limit your max output

Unless your tuner will do a touchup for cheap when the new one arrives?

Lol @ smash cat.

do it once do it right Trev, don't pay for 2 tunes coz you couldn't afford a real cat. You will need to retune if this one is a restriction and you change it later.

and yeah, you can YOLO it and smash it out. Mines permasmashed lol

I would have if it wasn't already so noisy. The plan is to smash it later and put a Varex mid muffler and retain oval rear muffler I have on it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...