Jump to content
SAU Community

Recommended Posts

that kia must be a laugh to drive....throw some m/ts on the front and go down the princes highway on a friday night...

cheers

darren

About 1 launch and youd snap something lol

Thought there might be some more interest in this thread,

I'm selling an SS1 I recently purchased for my RB20. Need the cash unfortunately.

http://www.skylinesaustralia.com/forums/topic/441479-sa-hypergear-ss1-turbo-brand-new/

Here my dyno results from my ss1.5 on my sr20det non VCt 180sx

266rwkw ss1.5 .86ar

250rwkw ss1.5 .64ar

251rwkw atr28g2 .64ar

Power vs boost

post-79144-13981680622387_thumb.jpg

Power vs torque

post-79144-13981681002793_thumb.jpg

Tuner said there was 5-10kw more in it if I replaced my dw300 fuel pump for a walbro 460lph pump as fuel pressure was dropping 10psi under load when tested but not worth the money and extra to tune right now as turbo is at it's max and injectors will be too as I'm on e85

The .86ar did gain 16rwkw but at 250rpm lag penalty and 5psi more down low and 2-3psi more up top

So it did make the engine happier as he could add in lots more timing and more boost

where as before I was capped to 20psi with .64ar or he had to remove lots of timing with more boost to the point power went down with more boost

Any dyno reading from that tune? The SS2 on Jared's car is the Black edition, with the latest compressor and larger turbine. It should be making power easier then the previous version.

A result sent in from an SS1PU customer. This is the latest version also that has a different compressor that is engineered to hold boost better and more top end.

It is running on E85 maxing out fuel pump. Peek of 301rwkws @ 17psi. With plenty of mid range.

From customer's feed back letter:

R34 GTT (Stock Motor)

Supporting Mods

Blitz FMIC Return Flow

1000cc Injectors

Standard Airbox (Panel Filter)

3inch Bellmouth Full Exhaust

Z32 AFM

Walbro 255 Fuel Pump

SS1PU (latest model)

Scotty's Alloy Intake

CALTEX E-Flex

301.8 Rwkw (18psi peak, drops off to 17psi holds well)

atr43ss1pu.jpg

Is this internal or external gate. Far out there are so many options haha, and I have the exact same mods and I'm getting it done at pulse racing... May save me some time

Drives a lot nicer now it's tuned to the .86rear

Part throttle still has power but haven't done a lot of driving yet as I just got it tuned

But I was surprised it didn't lose much response going from the .64 to .86 200rpm if they where both on 20psi was expecting it to be worse and laggier about 500rpm but engine is a lot happier

Should have waited alil longer as the atr28ss2 would have been a lot better everywhere and make more power down low and up top

Is this internal or external gate. Far out there are so many options haha, and I have the exact same mods and I'm getting it done at pulse racing... May save me some time

This is an internally gated bolton upgrade turbo that sits on factory manifold, dump, and water lines. It is an very responsive turbo for around the 260rwkws mark on P98 fuel. Alternatively you can run the new SS2 which would be good enough for 300rwkws on pump 98 fuel.

This is an internally gated bolton upgrade turbo that sits on factory manifold, dump, and water lines. It is an very responsive turbo for around the 260rwkws mark on P98 fuel. Alternatively you can run the new SS2 which would be good enough for 300rwkws on pump 98 fuel.

I'm missing something - I think his is on E85 and it maxed out making just over 260rwkw? Or you mean 300kw @ hubs?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Is it alright to top up with just another green coolant?
    • thanks GTSboy. My confusion at the moment is i am trying to locate the ignition, ECU battery power and the ECU negative The closest thing i can find is the for the S15 on Page 8 of the Wiring Specialties web page https://drive.google.com/file/d/0B9F33_M_GgENQnZ6STMxVmVNd1E/view?resourcekey=0-eZ4nNRwRoqa1qvKlWWHm8A I cannot find the same diagram for the R33 RB25DET Series 2 dash plug pin out.... Do you know what the Pins? or know where i can find the same pinout diagram for the RB dash plug? Thanks for the advice on the box... i like a 6 speed so might be on the lookout or the box now.. a topic of discussion for another post...
    • Will have a look at that. I cant see any leaks 
    • Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
×
×
  • Create New...