Jump to content
SAU Community

Recommended Posts

  • Replies 192
  • Created
  • Last Reply

Top Posters In This Topic

i am getting a set of the upper arms for the fornt and may get some rear arms

i could lift it one click on the ohlins i guess which would raise the old girl but that reakes of effort

i always shift at 7k in my rb26 powered cars.... probably why i dont duncan them all the time

the rb30's shift at 6200 as they have heaps of grunt down low

doesnt make any more power after 7 anyway.... my r31 which had a 3540 i shifted at 8k but it had grunt and forged things inside it!

:D

tell the truth. you shift at 7 cause you are flat out gay. you like the company of men. hairy ones with presents for you.

still can't deny you are a good looking bloke and have a toit body. yesh toit.

turbo is shit too. made heaps of noises when it was banging around loose in the boot of my car. at one point a spanner i had lying in the boot got jammed into the compressor wheel and when I pulled it out the farking head of it was gone. if you find my spanner head in your turbo, engine or cat then kindly post it back to me you cnt as without it my spanner is about as useful as your tiny penis. thank you.

tell the truth. you shift at 7 cause you are flat out gay. you like the company of men. hairy ones with presents for you.

still can't deny you are a good looking bloke and have a toit body. yesh toit.

turbo is shit too. made heaps of noises when it was banging around loose in the boot of my car. at one point a spanner i had lying in the boot got jammed into the compressor wheel and when I pulled it out the farking head of it was gone. if you find my spanner head in your turbo, engine or cat then kindly post it back to me you cnt as without it my spanner is about as useful as your tiny penis. thank you.

It sounds to me that you are some what jealous he's with men that are not yourself Baron????

Rhys

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...