Jump to content
SAU Community

Recommended Posts

jap average is around 15k even though for some reason everyone assumes otherwise. This is why it should be assumed that cars are wound back.

If they were such perfect low km examples, they would have been bought by the domestic market, not flogged to overseas customers at the auctions :)

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

I paid a good price :)

The car was imported in 2000 with 2,000kms on the clock. That owner had it for 2.5 years and put another 12,000 on it. So yeah - I was lucky. Just like a run-in new car.

I think a lot depends on locality. A lot of people in the Tokyo area only use their cars on the weekend, so a lot of those cars can go 2 or 3 years without putting on any serious K's. Where I am, out in the mountains, there isn't much public transport, everything is spread out and owning/driving a car on a daily basis is just about unavoidable...

in the last 2 years I've owned the car I think I put about 25000 k's on the car. I got it at a cool 40000k's (with books and service manuals from a nissan authorised dealer to back it up) and the servicing was as regular as clockwork too, I think the previous driver was a hot jap babe or sumfin (knowing my luck it'll be a non-milfish mom).

Bought the car 2 1/2 years ago with 42,000 on the clock. The condition of the car and the log books matched the KM stated.

Now it's up to 85,000 and hasn't missed a beat.

Had the front castor rod thingies replaced but that's it.

J

bought it with 65000km, now 96000km. Bought it in july 2001. travelled 200kms a week to work, major problems was the worn front castor bushes and busted stock clutch(what do you expect from 180rwkw@CAS) otherwise a great car. 100000km major service now due along with worn rear tyres.

How much did it cost to get these replaced and what difference if any did you notice after they had been replaced ?

G'day Ben,

I had the same problem. The factory castor rod bushes are filled with some sort of gell/fluid stuff and are prone to leaking.

Mine were picked up at the last wheel alighnment I had done.

I couldn't tell you if there was any handling improvement cause at that stage I went from the JIC coilovers to standard shocks with 25mm lower springs (hence why I got the alighmnet done :D ).

One thing I did notice was that it now has a slight squeak sometimes !

I think the cost was $120 for the parts and about $60 for fitting.

Cheers

J

I had the front bushes replaced in my car and noticed a difference in the turning response. It was a lot quicker and sharper. The stock ones were shot, had tears in them. I got the polyurathane ones (i think thats what they were made of) and they are a lot stiffer than the old ones.

I got mine a bit over 2yrs ago with 62 000k and just tonight clocked over 110 000k, the only problem I have had is the crank case seal went about 6 months ago otherwise perfect. That includes skidpan and track days, many runs down the 1/4 at willowbank and trips to Sydney from Brisbane. Been a great car so far.

Edit: Oh yeah forgot, had to do the caster bushes when I first got the car.

I bought mine with 101 000 on the clock and got the timing belt done. The mechanic said it was its first belt (becuase it was so shagged) so there is a good chance the km's are geniune. Now there is 123 000 ks on the clock. I have driven about 20 000ks in about 8 months, so my new years resoultion is to start catching the bus to work and leave the car at home to keep the ks down.

I also had to get the castor bushes replaced because they were leaking oil. Couldnt notice any handling difference because I only had the car a day when I got the work done.

Other problems with it were the clutch (general wear & tear I'd say) and a couple of exhaust manifold studs missing. Other than that, i think its a healthy RB20.

Changed the plugs a couple of days back (about 30 000ks old) and they seemed to be in pretty good condition (all had the same sort of wear).

/end rant

got it with 89,000kms, have now done 145,000kms..

only problem was the muffler which I replaced it when i first imported it...and just recently somethings shorting out in the steering column causing the indicators to go haywire (still to be fixed).

I bought my '33 with 74,000 on the clock (skeptical), now has 164,000. Only things that have gone wrong is the clutch (it just wore out) and the ECU stopped sending tacho signals, but otherwise worked perfectly?? The only problem with the engine is one lash adjuster seems to be worn so it has a light ticking noise occasionally, but otherwise it's been 100% reliable. I service it every 5,000km -7,500km with full synthetic oil and filters changed etc and treat it with mechanical sympathy, so that's gotta help longevity.

Seems a lot of people have had problems with the radius rod bushes tearing etc. (Just as I did) The mechanic told me when I had mine replaced that they quite often fail by 60,000kms.

Those of u that have replaced them, are u getting the stiffer ones or the stock ones from nissan.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • The roof is wrapped
    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
×
×
  • Create New...