Jump to content
SAU Community

Recommended Posts

4th gear stopping before limiter. I have alot of mechanical sympathy :)

Limiter is 8k. I like my stock rod bolts non stretched :D

Hmm. Something is up. 4th at 8000 RPM is 235 km/h and you're going to 190 ish km/h which is 6400 RPM. :S

Could the road speed on the dyno be wrong or something?

It's only my gay 4door gtt that needed so much fuel system work

But hey Can't complain with 367 @the wheels

At least your gay gtt runs ya kent :P stupid flex fuel!!

Nice result so far! Though to be fair I'm not sure if the PT6262 will really be showing its mettle yet, have you had any stock RB26 with a GT3582R on E85 on that dyno? That would make for a very interesting comparison

No i havent. This is the first single on rb26 on this dyno.

I wish i had a forged motor so i could run 35psi. I think it be close to 500kw

took it for a cruise to get some pizza. Without finishing the tune down low it drives very nicely. Below 3 very little boost. Above it picks up nicely.

So are the Precision turbos their own CHRAs or common with Garret. I am looking at either a FP73HTA with one of these housings but also considering a Precision turbo...but makes life easier it i can run one of these rear housings

http://www.atpturbo.com/mm5/merchant.mvc?Screen=PROD&Store_Code=TP&Product_Code=ATP-HSG-075&Category_Code=

Has anyone worked out the rpm vs speed yet..?

How fun would that turbo be on a 3lt

PT6266 would be more fun :D There are quite a lot of Supras running them, they seem like a pretty brutal all around setup.

Off topic, Jez u get the pic etc? I have the same issue as Kurtis :(

Hey buddy, yes i got the pic. Very dissapointing i was sort of hoping it was an odd issue with Kurtis's car, but if its happened on a different car with another workshops setup makes it very annoying. Hopefuly warranty wont be an issue.

Txt sent

How does the turbo sound when your up it Jez?

I've been told they are rather quiet compared to most singles...

On the dyno from in the car with headphones on i couldnt really tell. U can definately hear it spool up like a jet when inside the car but i havent been incar with a similar setup so cant compare.

No i havent. This is the first single on rb26 on this dyno.

I wish i had a forged motor so i could run 35psi. I think it be close to 500kw

took it for a cruise to get some pizza. Without finishing the tune down low it drives very nicely. Below 3 very little boost. Above it picks up nicely.

No prob Jez , just put it onto mine and see what it will make :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...