Jump to content
SAU Community

Recommended Posts

Chris, post 55! The first type is the one I have, but it's overkill for wheel nuts, more for engine building. I just picked it up cheap.

For wheel nuts just pick up a spring type one, they reset automatically between use so are more convenient as well as cheaper.

Also post 20 made me lol

Actually torque wrenching wheel nut for me is quite funny,,,I only actually torque Duncan's up to appease him,,,I'm that bloody good I can do them up to 110 newtons with just a breaker bar. Test me one day,,,you will be shocked. Maybe in hindsight I should have tighten his wheels nuts at targa years ago and he wouldn't have lost the left front wheel.

But I digress,,,the 'Snap On" left handed drill/extractor kit is the ducks guts. I pin punched the 1st bolt and started drilling,,,it came out before ever breaking the surface. The 2nd bolt took a little longer and no need for the extractor. This is indeed a cool tool.

post-29-1290675987_thumb.jpg

post-29-1290676001_thumb.jpg

Cheers

Neil.

been doing alot of wiring lately so these 3 new tools have been the ultimate in making it go fast and neat.

left : Narva non insulated connector crimpers

centre: Kincrome insulated wire crimpers

right : kincrome automatic wire strippers

worth their weight in gold

post-5157-1290830439_thumb.jpg

Lots of tool sales on yesterday.

Picked up myself a 3 piece Irwin Vice Grip set, 5 piece Irwin Pliers set, Stanley FatMax saw and a Toolex 8 piece T-Handle Hex kit. No idea if I need any of them but the prices were too good to knock back.

Was considering a Cordless Impact Wrench but couldn't decide between the Dewalt or Hitachi and can get them off Ebay for the same price any day of the week so walked out with none ;)

Ben....we need to know before the sale, not after!

Neil.....

portable-ac.jpg

also, speaking of torque wrenches I bought these the other day....1/4" and 3/8". Will still use the 1/2" beam style for important stuff like motors.

torque-wrenches.jpg

It's a real shame that no one imports Craftsman tools here in Oz. Craftsman is Sears & Robuck brand in the US. They've always made good quality spanners and sockets at really competitive rates. I've still got a lot of my sets from when I lived in the states 10 years ago. When I go back next year I plan to bring back a fair bit.

Just noticed Bunnings has some craftsman tools on the shelf now, and of course they can special order anything from a brand they carry, and will price match as well. Oh, and for legal reasons I should disclose that I may work at Bunnings haha :thanks:

[Edit]

I should add that this is what we had on the shelf - These deserve a mention in the cool tools thread; ratcheting elbow spanners - Would be great to undo bolts where you have no room to swing a spanner, or even a ratcheting spanner. The elbow allows you to undo bolts by pushing and pulling the spanner; genius idea.

The Image is here http://images.bizrate.com/resize?sq=500&uid=1609186795 - Image tags won't work for me on this fancy newlook forum

  • 2 weeks later...

Arthur did you break any glass removing it? my last attempt was 2 broken from 6 so I never tried again. cheaper to get a windscreen bloke out to do it :(

Picked up one of these at supercheap today because no decent shop was open. $120 and looks pretty good surprisingly.

engine-stand.jpg

yeah for sure. in fact I can't think of many motors longer and heavier than a complete rb26. but this has reasonable design, box sections and bolts. better than I expect from supercheap

Arthur did you break any glass removing it? my last attempt was 2 broken from 6 so I never tried again. cheaper to get a windscreen bloke out to do it :(

I've only done one and i didnt break it..

It does take some patience to make sure you have cut all the goo away before you start pushing on the screen..

But the tool only cost me 35$ from a windscreen warehouse. Its a pretty basic tool, you could probably make one easy enough..

I got the grinder onto the blade to make sure it was real sharp and you have to keep cleaning the goo off it..

Actually torque wrenching wheel nut for me is quite funny,,,I only actually torque Duncan's up to appease him,,,I'm that bloody good I can do them up to 110 newtons with just a breaker bar. Test me one day,,,you will be shocked. Maybe in hindsight I should have tighten his wheels nuts at targa years ago and he wouldn't have lost the left front wheel.

Cheers

Neil.

oh lawd!

  • 3 weeks later...

Rofl,,,you stick to the scissors mate,,,I'm over cutting radiator hoses and the like with them. I'm into nice and neat hoses. My old adage is "If you can't go quick look good".

Moving on,,,heres 2 of my 1/4 drive sockets sets.

post-29-1278415762_thumb.jpg

This one is one I bought,,,it's a Kokon set ,,,Japanese brand,,,not rubbish which I'm liking. If I had the money I would buy all their products.

post-29-1278415778_thumb.jpg

This one is Kinchrome which was nicely donated to me by Duncan,,,still not quite sure why,,,maybe all my losed blood over the years. It's a great set as well being AF and Metric which suits me.

Cheers

Neil.

Where did you get that koken socket set out of interest? I have heard good things about them here and there, but can't find where to buy them

  • 2 weeks later...

Love this thread... been meaning to put something up.

Changed my brake rotors, brake lines, brake fluid a few weeks ago... these came in handy.

$10 - bleeder kit.

And I was a few jack stands short so a few bricks took care of that.

post-74159-0-68551700-1296692730_thumb.jpg

post-74159-0-69892500-1296692740_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...