Jump to content
SAU Community

Recommended Posts

Anon32... this week ive used mine.to remount power steering resivour, mount catch can, attach front bar where old mounts got broke, anytime you work with sheet metal and dont want/cant get ya hand in yo do up nuts

  • Like 1

Are the gas ones better than the Diesel ones im bunnings i see atm? I was thinking of buying a Diesel one as i thought the diesel might last longer than the gas cylinders?

Pros for diesel.

Easy to refill.

Smaller

A leak won't explode you to death

  • Like 2

Well, just fired it up. The fan was stuck on the shroud and it only runs true when you put some weight on the housing. hehe, will take a few little mods.

I've had an oil one in the US. When it clogged and got a blow out smoke would billow out. I don't think the LPG one will do that.

I just want to use it every now and again. Primarily to take the chill off when I'm in there for 2 or 3 hours at a time.

Well, just fired it up. The fan was stuck on the shroud and it only runs true when you put some weight on the housing. hehe, will take a few little mods.

I've had an oil one in the US. When it clogged and got a blow out smoke would billow out. I don't think the LPG one will do that.

I just want to use it every now and again. Primarily to take the chill off when I'm in there for 2 or 3 hours at a time.

Don't be tight, rip up the concrete and install heater tubes in it :)

Can't wait to fire up this bad boy!

So I used it today. Worked great. Didn't smell that bad at all and sure took the chill off quickly.

https://www.facebook.com/eric.yamashita.96/videos/1023814724310442/?l=2465421167051501678

  • Like 1

So I used it today. Worked great. Didn't smell that bad at all and sure took the chill off quickly.

https://www.facebook.com/eric.yamashita.96/videos/1023814724310442/?l=2465421167051501678

Would be cool to find some biodeisel for it - ex french fry oil would smell pretty good :yes:

  • 3 weeks later...

I needed a spare 1/2" ratchet for my "cruise" toolkit (the one that leaves the house) -picked this set up at Repco for $59 (I gather they're clearing out their Sidchrome gear).

7190.jpeg?etag=%22b047c19bfbaa544b4461e7

They don't feel as strong as my older Sidchrome ratchets, but for the price I can't complain.

Also returned an old Repco 1/4" ratchet that I must have had for six or seven years. The bearing on the head was worn so sockets etc were just falling off; can't fault their warranty and service the bloke at the counter swapped it for a new one on the spot and no questions asked. Will definitely be recommending their tools to anyone who asks.

  • Like 1
  • 3 weeks later...

Really doing best to keep this thread alive lol

Snagged a set of Sidchrome 440 series spanners from my mates at Repco Chatswood today. The past couple of times I've been in there buying oil/filters/etc I've noticed these guys in the display case marked down to $119. Today temptation got the better of me. They had a few more sets and as I suggested above it seems that Repco as a brand are divesting themselves of Sidchrome stock so a good time to tool-up. Yes they have the lifetime replacement warranty.

440_zpsrb2oxul5.jpg

  • Like 2
  • 2 months later...
  • 2 months later...

If you had to buy a good price/quality toolset, which one would you get ?

Got a cheap and crap one a while ago and snapped a few tools already so I'll spend a bit more to get something decent but tool brands are different to Europeans one and not sure what to go for.

Stanley is the only brand I had before so if there is other good quality tools that are affordable for the Sunday kind of work, I'm listening :)

If you had to buy a good price/quality toolset, which one would you get ?

Got a cheap and crap one a while ago and snapped a few tools already so I'll spend a bit more to get something decent but tool brands are different to Europeans one and not sure what to go for.

Stanley is the only brand I had before so if there is other good quality tools that are affordable for the Sunday kind of work, I'm listening :)

By tool set what do you mean? Spanners, sockets?

I find that repco tools are OK. A little higher quality than Stanley and still reasonable priced.

Update on the rivnuts. Got to use it for the first time with some m4 nuts. Worked great. Took more time to drill the holes than install the rivnut. And it really looks professional.

post-16200-14500874956942_thumb.jpg

post-16200-14500875162898_thumb.jpg

post-16200-14500875328893_thumb.jpg

post-16200-14500875484893_thumb.jpg

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...