Jump to content
SAU Community

Recommended Posts

I'm looking to buy some new 18 inch Work XT7's and need to know what offset and width I can go. I was hoping I could fit 9.5 inch as I think they would just fit with a little guard massaging.

I don't want spacers so I need to get this right first time. Any ideas guys?

post-63525-1279295509_thumb.jpg

I'm looking to buy some new 18 inch Work XT7's and need to know what offset and width I can go. I was hoping I could fit 9.5 inch as I think they would just fit with a little guard massaging.

I don't want spacers so I need to get this right first time. Any ideas guys?

Hey Scotty,

Spoolin and I worked out that the perfect fitment is a 9.5 with a +35 offset for the M35.

This will get it flush to the body without any rolling of guards and clear the front suspension arm by about 7mm. So no mods to the body and 100% no scrubbing.

It will also mean you get that deeper spoke pull on the XT7's that make them look soo good!

Im pretty sure the XT7 come in a 18x9.5 +38 which would be sweet with a 3mm spacer to give a little extra clearance on the front suspension arm (if it wasnt for that arm, we could easily fit 10.5 to 11" all the way round!

Edited by bbenny
Hey Scotty,

Spoolin and I worked out that the perfect fitment is a 9.5 with a +35 offset for the M35.

This will get it flush to the body without any rolling of guards and clear the front suspension arm by about 7mm. So no mods to the body and 100% no scrubbing.

It will also mean you get that deeper spoke pull on the XT7's that make them look soo good!

Im pretty sure the XT7 come in a 18x9.5 +38 which would be sweet with a 3mm spacer to give a little extra clearance on the front suspension arm (if it wasnt for that arm, we could easily fit 10.5 to 11" all the way round!

As Scotty stated he didn't want spacers, sucks that it is hard to fill the guards without having to add spacers.

If the suspension arm has 7mm clearance and he went with a +38 rim, that would reduce the clearance to 4mm. I assume this would be running too close for comfort?

Mmm 4mm is cutting it close as there is flex in those parts. I would rather push them out a bit more and rollll. ;)

Looks like +30's are the go then?

+ 30 will be fine, you will just have to roll the lip on the rear guard or just run a tyre size down so they are a little more stretched.

I just would be careful on the front guard.

Here is how a +35 sits on my car - as you can see its pretty flush up front. So +30 will sit 5mm further out, the rear will be fine with just a roll if needed, but the front guards are already rolled.

Honestly you will be fine with a stretched tyre.

_MG_7823.jpg_MG_7824.jpg

_MG_7827.jpg

  • 1 year later...

Sounds about right.

I provided that to Braid, and they said they'd suggest an 18 x 8 +40-42, but because they were a wider rim they'd sit out more and fill the guards a bit better.

So that's probably the way I'll go. A nice set of these:

1222869591.preview.jpg

http://samotorsporttyres.com.au/content/winrace-1

Sounds about right.

I provided that to Braid, and they said they'd suggest an 18 x 8 +40-42, but because they were a wider rim they'd sit out more and fill the guards a bit better.

So that's probably the way I'll go. A nice set of these:

1222869591.preview.jpg

http://samotorsportt...ntent/winrace-1

+40/+42 would look crap. go minimum +30...

an 8 inch rim isn't that wide...

Agreed!

I ran AR-X 18x8 +40, but when I went to V35 18x8 +30; looks so much better! Consider +30 the absolute minimum; then get a little braver.

Also make sure you don't go too small on rolling dia, even 20's can get swallowed up in those big wheelarches if you go too low a profile.

Yeah you need atleast an 8.5+30 to near fill the guards.

mine were 8.5 +20

they sat awesome. 5 or 6 mm out the guard. worked well because of the ARX over fenders.

I'm getting tyres fitted Saturday. I'm looking at a 245/45-18 as there is a greater choice in that size. Also thinking of a 235/45-18 to get a little stretch to help clear the guards. Not that big of a choice in that size either. I like the fact the 245/45-18 is a little taller than stock to help correct the spedo a little. I'm assuming all m35's read higher than actual speed. Just hope they don't hit the guards on bumps or steering lock.

I'm looking at nexen n1000, anyone had any experience with these?

Edited by slippylotion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I drive the Tiguan much harder than the Skyline in all conditions, because it just grips and hooks, unlike the R33 shit box
    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
×
×
  • Create New...