Jump to content
SAU Community

Recommended Posts

I'm looking to buy some new 18 inch Work XT7's and need to know what offset and width I can go. I was hoping I could fit 9.5 inch as I think they would just fit with a little guard massaging.

I don't want spacers so I need to get this right first time. Any ideas guys?

post-63525-1279295509_thumb.jpg

I'm looking to buy some new 18 inch Work XT7's and need to know what offset and width I can go. I was hoping I could fit 9.5 inch as I think they would just fit with a little guard massaging.

I don't want spacers so I need to get this right first time. Any ideas guys?

Hey Scotty,

Spoolin and I worked out that the perfect fitment is a 9.5 with a +35 offset for the M35.

This will get it flush to the body without any rolling of guards and clear the front suspension arm by about 7mm. So no mods to the body and 100% no scrubbing.

It will also mean you get that deeper spoke pull on the XT7's that make them look soo good!

Im pretty sure the XT7 come in a 18x9.5 +38 which would be sweet with a 3mm spacer to give a little extra clearance on the front suspension arm (if it wasnt for that arm, we could easily fit 10.5 to 11" all the way round!

Edited by bbenny
Hey Scotty,

Spoolin and I worked out that the perfect fitment is a 9.5 with a +35 offset for the M35.

This will get it flush to the body without any rolling of guards and clear the front suspension arm by about 7mm. So no mods to the body and 100% no scrubbing.

It will also mean you get that deeper spoke pull on the XT7's that make them look soo good!

Im pretty sure the XT7 come in a 18x9.5 +38 which would be sweet with a 3mm spacer to give a little extra clearance on the front suspension arm (if it wasnt for that arm, we could easily fit 10.5 to 11" all the way round!

As Scotty stated he didn't want spacers, sucks that it is hard to fill the guards without having to add spacers.

If the suspension arm has 7mm clearance and he went with a +38 rim, that would reduce the clearance to 4mm. I assume this would be running too close for comfort?

Mmm 4mm is cutting it close as there is flex in those parts. I would rather push them out a bit more and rollll. ;)

Looks like +30's are the go then?

+ 30 will be fine, you will just have to roll the lip on the rear guard or just run a tyre size down so they are a little more stretched.

I just would be careful on the front guard.

Here is how a +35 sits on my car - as you can see its pretty flush up front. So +30 will sit 5mm further out, the rear will be fine with just a roll if needed, but the front guards are already rolled.

Honestly you will be fine with a stretched tyre.

_MG_7823.jpg_MG_7824.jpg

_MG_7827.jpg

  • 1 year later...

Sounds about right.

I provided that to Braid, and they said they'd suggest an 18 x 8 +40-42, but because they were a wider rim they'd sit out more and fill the guards a bit better.

So that's probably the way I'll go. A nice set of these:

1222869591.preview.jpg

http://samotorsporttyres.com.au/content/winrace-1

Sounds about right.

I provided that to Braid, and they said they'd suggest an 18 x 8 +40-42, but because they were a wider rim they'd sit out more and fill the guards a bit better.

So that's probably the way I'll go. A nice set of these:

1222869591.preview.jpg

http://samotorsportt...ntent/winrace-1

+40/+42 would look crap. go minimum +30...

an 8 inch rim isn't that wide...

Agreed!

I ran AR-X 18x8 +40, but when I went to V35 18x8 +30; looks so much better! Consider +30 the absolute minimum; then get a little braver.

Also make sure you don't go too small on rolling dia, even 20's can get swallowed up in those big wheelarches if you go too low a profile.

Yeah you need atleast an 8.5+30 to near fill the guards.

mine were 8.5 +20

they sat awesome. 5 or 6 mm out the guard. worked well because of the ARX over fenders.

I'm getting tyres fitted Saturday. I'm looking at a 245/45-18 as there is a greater choice in that size. Also thinking of a 235/45-18 to get a little stretch to help clear the guards. Not that big of a choice in that size either. I like the fact the 245/45-18 is a little taller than stock to help correct the spedo a little. I'm assuming all m35's read higher than actual speed. Just hope they don't hit the guards on bumps or steering lock.

I'm looking at nexen n1000, anyone had any experience with these?

Edited by slippylotion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...