Jump to content
SAU Community

Recommended Posts

i think the 7163 is a bit small for a high boost rb26, as it can be overspun. Same with 7670. however they both provide excellent spool and response so if you use a shaft speed sensor to keep things in check you could be very happy with either on an RB26 - just be prepared to taper the boost up top. The 8374 comes on strong around 3300-3400rpm - so it might be bigger than you like, but i really enjoy it on the RB26 (its one of my all time favorite turbo/engine combinations, so much fun to drive). I am putting the 8374 0.92 back on my RB26 in a couple weeks, after i put the 7163 on my evo

Geoff if you get a chance chuck up the graph for the 26 and 8374...

One day when I'm feeling rich I might do the swap from my 6262

Geoff if you get a chance chuck up the graph for the 26 and 8374...

One day when I'm feeling rich I might do the swap from my 6262

I second lol !! However, my next purchase is planned within the month ( depending if my turbos are actually shot or not)

  • 3 weeks later...

With the internal gated single, say an 8374, do you just use the external gated twin scroll manifold and just block the two gate runners off? I can't see a internally gated option for the manifold.

The other day i saw the McLarens V8 engines they are using in their MP4 & P1. Intersting to note the turbos look a hell of a lot like internal gate EFR turbos hanging off the manifolds

Funny thing is I have a pic in a book at home of a Pontiac Solstice turbo setup (I think?) which featured a twin scroll internally gated turbo with an integrated BOV in the compressor cover (I got the book before EFRs existed)... hard to say what else uses them, or similar ideas, but I found it really interesting.

^ Are those factory turbos manufactured by Borg Warner by any chance?

**EDIT**

After a little bit of research, the turbos for the McLaren M838T engine are sourced from MHI

Edited by Tonba

I can't remember specifically, I just recall the EFRs looking familiar when I first saw them and then later remembering how interesting the ones in the book looked. When I get home tonight I'll try and remember to look it up and maybe post a pic

  • Like 1

I don't know of any reliable OEM ones yet, so I am guessing it's for the same kinds of reasons. The late model Porsches are frequently going back for warranty claims, afaik.

  • Like 1

With the internal gated single, say an 8374, do you just use the external gated twin scroll manifold and just block the two gate runners off? I can't see a internally gated option for the manifold.

Full race have an iwg manifold option

http://www.full-race.com/store/efr-turbo-manifolds/nissan-rb26-25-20-det-t-twin-scroll-iwg-efr-turbo-manifold.html

Though id go the 1.05 rear twin ewg option on your car thats the setup I run and I can only imagine with the 2.8L it would be even better :)

  • Like 1
  • 2 weeks later...

I initially though they were airwerks due to the fact the FMW compressor wheels are apparently the same wheels as EFRs.

But then I saw the pic of what they actually run, which looks to be a custom casting.

borg-warner-turbochargers-used-in-the-iz

So can we buy these goddamn things or what??? Lol... particularly if we can get it with the 1.45A/R turbine housing.

Edited by bigmikespec

So can we buy these goddamn things or what??? Lol... particularly if we can get it with the 1.45A/R turbine housing.

EFR 9180 1.05 a/r is in stock, the 1.45 a/r starts shipping in 1-2 weeks.. making progress :)

With the internal gated single, say an 8374, do you just use the external gated twin scroll manifold and just block the two gate runners off? I can't see a internally gated option for the manifold.

you can block the WG ports off or use a non-wastegated manifold. here is our RB26 IWG efr turbo manifold:

75012_10151372490682527_2031045298_n.jpg

Full race have an iwg manifold option

http://www.full-race.com/store/efr-turbo-manifolds/nissan-rb26-25-20-det-t-twin-scroll-iwg-efr-turbo-manifold.html

Though id go the 1.05 rear twin ewg option on your car thats the setup I run and I can only imagine with the 2.8L it would be even better :)

the twin wastegates are the call for maximum performance. I hope you are happy with the setup!

So which one should provide a better spool the IWG 0.92 or the EWG 1.05 ? or wastegate don't really affect spool up, only boost control ?

the smaller a/r will usually spool the turbo quicker.. as long as the wastegate doesnt crack open prematurely it wont affect spool. The solution is to use a stiff WG spring. turbosmart IWG has been popular lately becuase it uses the same springs as their EWG (up to 3)

I can't remember specifically, I just recall the EFRs looking familiar when I first saw them and then later remembering how interesting the ones in the book looked. When I get home tonight I'll try and remember to look it up and maybe post a pic

i believe BW made the turbos for that saturn skyy/pontiac solstice platform. as well as the cobalt. And the 2011-2012 EcoBoost F150, and 2012+ Focus ST EcoBoost, Fusion, etc.. audi and volvo they all used that style Compressor recirc valve. It works well

Yes I know you can buy housing separately, it would be nice if you can just buy one direct from BW or even from a Indy team???

indy teams now run twin EFR7163 only. there may be some used 9180s floating around, but keep in mind it was not in a ported shroud housing so actually the standard EFR9180 compressor housing will slightly outperform the indy 9180 - given the same turbine housing A/R

Edited by Full-Race Geoff

indy teams now run twin EFR7163 only. there may be some used 9180s floating around, but keep in mind it was not in a ported shroud housing so actually the standard EFR9180 compressor housing will slightly outperform the indy 9180 - given the same turbine housing A/R

What is the reason for switching to the twins?

I would have thought the opposite as the surge slots bypass air to avoid surge hence efficiency losses.

Any plans to bring the mixed flow turbine wheel into other sizes apart from the 7163? If so, what would be the better ass end. The open scroll mixed flow or the twin scroll?

Also very interested in this.

Also interested if BW are looking at a 64mm turbo to fit between their 8374 and 9180?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...