Jump to content
SAU Community

Recommended Posts

FI are still yet to launch their new car thats why it looks the sam, same for Virgin and Mclaren, although I find it weird that Virgin have a fully connected shark fin in that pic even though they never had one last year and they are banned for 2011.

FI are still yet to launch their new car thats why it looks the sam, same for Virgin and Mclaren, although I find it weird that Virgin have a fully connected shark fin in that pic even though they never had one last year and they are banned for 2011.

Red bull seem to have a shark fin type thing.. however it doesnt extend all the way back, more cheekyness from adrian newy?

Red bull seem to have a shark fin type thing.. however it doesnt extend all the way back, more cheekyness from adrian newy?

I read somewhere that the Red Bull shark fin extends to the absolute maximum that the regs will allow, leaving only the minimal gap required, surprising to see that they are the only ones to really to do it yet.

thanks for the pics. wow. some of the cars are really radically changed compared to last year. which I guess is to be expected given the regs. look at the front wings. my god could they get any more complex? not much chop when you bang wheels with kobayashi and loose half ya 'bits' on the first lap though...

These were a couple I used last year:

http://www.vipstand.me/

http://www.tvkorner.com/

Good for watching practices and quali's and having on the laptop for when channel one goes to commercial, but neither were tv quality picture.

The new Pirellis dont that THAT bad on the McLaren, sure white or red would suit better but its still not exactly an ugly look

They just have large signage on the launch & test cars so everyone knows who the tyres belong to. By the time they start racing properly the tyres will be covered in black so you wont even notice the branding. Hell half the time it was near on impossible to pick who was on what tyre anyway.

Anyway McLarens look better in orange so who really cares.

Edited by djr81

Check out the 3D model of the MP4-26 on the McLaren racing site; Serious looking exhaust blown wing setup. Looks to be supplemented by some scoopage near the airbox inlet.

Now let's see the relative PACE!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...