Jump to content
SAU Community

Recommended Posts

ARTZ, you make me sad.

i would've purchase your whole setup if only you put it up earlier. maybe convince handaldo to buy it all off you lol

hope it all goes well for you mate.

Hand... Aldo? Is that me?

I believe that joey was running 320rwkw with Nismo 550's on E85 with his 2835pros

Even if they don't cut it, run as much boost as you can to get to about 95% duty cycle :thumbsup:

How is that good advice?

I still dont see how 550's could come close to flowing enough, even at stupid rail pressures. Like I mentioned Artz, chase up a Neo rail and get some ev14's shoehorned in there.

aahhhhhhhhh........ok f**k it.....

I'll finish what I started, on the cheap..then if I'm still sick of it, I will sell it...

sale on hold till further notice... :whistling:

one Q...will 550 nismos cut it...???

I know most are running the 740s but how much headroom is there??

why dont you just do what i did and pay $300 to get the stock side feeds hi-flowed?? mine are 90% @ 340kw...

Or maybe you should buy mine and i will get some ID1000cc with some valve springs then wind up the boost!

wrong person, i mean to say rondofj :P

tschh..Im still off the road for another 2+ months, well yesterday I fitted in my new JJR dump/front and new O2 sensor and cannot be happier with the instant response and pull factor..still some way to go..new injectors and afm..before I get the Kando or HG..ya ya I know my new dump will need to be modified if I go Kando..:blink:

yeah im keen n the ev14ks now actually, the smallest of them, need to find a neo rail on the cheap though to make it viable....

http://www.bosch-mot...alves/EV_14.pdf

why not just get these and plug connectors from bursons..

http://www.ebay.com/itm/Siemens-Deka-60lb-EV1-SHORT-High-Imp-Fuel-Injectors-6-/390213457860?pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr&hash=item5ada88d7c4

i remember reading on the xr6 turbo forums that the siemens injectors require some different tuning paramaters to most factory injectors. my memory says injector pulse width?? whatever it was, once the parameters are set correctly they idle very well.

ARTZ, finish what you started.

Once you sell and the new commitment comes along you wont be seeing any play money again for a while... 1K is a couple of weeks overtime, suck it up and keep at it!

hahaha....I know you could do it too.. :rofl:

yeah Scotty to the rescue...I went to hire a trailer mate, was 120$ + stuffin around, So i rang my towie, he will drop it and pick it up for 100$...legend!!!

those deka injectors are dirt cheap, can get a blank fuel rail for about 30-40$ yeah..wonder if we could make the stock reg fit..

I was talking to another bloke today reckons they are fine as long as you get a dampner in the fuel line.. :unsure:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I think the consensus was that's normal. Sloped road surfaces or something? I remember @silviaz went through this before. It might be one of those things you never notice until you pay attention to it.
    • Im not entirely sure exactly what or where its leaking from, he started to pull the boots to swap to my new tie rods + ends and it just vomited fluid, so he closed em up up, swapped the rod ends to the old rods and let me know so I can figure a solution out, im guessing its all origional as as I passed 103k miles earlier this year im sure its just in need of a full overhual/rebuild anyways.    If i could just yank it off and be good it wouldn't be an issue to ship it out and wait for the turnaround but the guy I work with doesnt really have space to keep my car for a week or two at a time, would rather drop it off and have a replacement ready to drop in
    • What do you mean by "seals"? Internal hydraulic seals (ie, is it leaking PS fluid?) or the rack boots that close the rack onto the tie-rods? Because the former is a rebuild, and the latter is trivial that you or any nearby mechanic could do. Dunno about the cowl. Just buy what you think is required and get anything else you find/break afterwards. Wing? Dunno. Don't like R33s enough to pay attention to them. Mirror glass is just glass (on the surface that you want to polish). Go for it.
    • Hello! Long time lurker, been using the forums to address concerns and questions from afar for a while but I've struggled to find some answers so I guess its about time I made an account and formally asked some more knowledgeable people, since finding local skyline owners is hard (and shops that are knowledgeable or trustworthy to work on 'rare' cars are non existent out where im at, as skylines are quite uncommon to find in the wild around here). So the main 3 questions I have, 1: Steering rack has blown seals, well.. they kind of hold but they are not sealed properly anymore and as my R33 is my DD, i cant exactly rip the rack out and send it off or attempt to fix myself. As most refurb ones are around $1,100 or more shipped, and I have other things I need to work on around the car, I was seeking clarification on whether an S15 rack will more or less bolt right in, and whether a common mechanic could do any other required work to get it to fit. I ask, as I've found a supplier than can sell a manufactured as oem one for around 400, if not I'll likely order a used one from Jacks JDM, and take a risk on the seals there. The second question i have is that im replacing the front wiper cowl and have planned to buy 4 new clips and a new center clip but wasnt sure if there were any other clips that would also need to get replaced while I was at it. Given im sure any that are there now will simply break when I remove the old cowl... Last thing would be a fairly straight forward question, i think. If I manage (strong if, finding one has proven to be a pain) to find a R33 GTR spoiler/wing will it require much modification to bolt to a S2 R33 GTST? I've read the bolt patterns dont match but otherwise would bolt in, only options I have found with much luck is China stuff on ebay and carbonetics, which has a nice $650 shipping fee... so if anyone has any pointers where a US chap could locate one that would be great Random side question as well, the mirrors as I understand are mirror glass, and as im planning to polish my windows from water spots and surface scratches, i was hopeful cerium oxide would be fine for them too, as my research points to, but clarification is always nice. Any pointers would be appreciated, and while I have scoured the internet for answers if I missed a prior post somewhere that may answer these directly please point me towards it, as i must have simply missed it. I have seen a post here or there that has mentioned it, but I usually get 50-50 answers, or half answers... I dont have a lot of fab experience or mechanic experience, outside of hydraulic and pneumatic stuff I did in the military and with how hard it is to source stuff in the US, id rather not wing it and hemmoraghe money lol. Thanks guys! Sorry for the monumental first post haha
    • Yep, there's a very minor drift left that happens a few seconds after letting go of the steering wheel, but not enough to bother me. Enjoying the car still!
×
×
  • Create New...