Jump to content
SAU Community

Recommended Posts

Not what I did to my stagea, but more what I did WITH it..

On the way to nightwars (a summer drag racing series), threw sparks all over everyone elses cars, popped a couple cats eyes out of the road and now all I can smell is hot metal... Flexi in the exhaust looks worse for wear and so does the rear tow hook... Might need to raise it. :(

Not what I did to my stagea, but more what I did WITH it..

On the way to nightwars (a summer drag racing series), threw sparks all over everyone elses cars, popped a couple cats eyes out of the road and now all I can smell is hot metal... Flexi in the exhaust looks worse for wear and so does the rear tow hook... Might need to raise it. :(

Don't do it!:spank: As an extension to the "Don't buy wheels that fit the car; make the car fit the wheels" ethos; I propose a "Make the road suit your ride height" solution.

You just need to keep frequenting the roads you use; until you've worn a groove them all to suit your ride height, no more clearance issues.

Anything still grinding will eventually be worn away; consider these items "Surplus to requirement" Problem solved.:thumbsup:

You're welcome.:whistling:

Edited by Daleo

ok this is what i found............. so basically its a wait of money.

Posted 27 April 2011 - 02:24 PMsnapback.pngironpaw, on 27 April 2011 - 01:55 PM, said:

Anyreason these won't work for our cars?

http://www.importmon...%20NM35%2014750

review: http://my350z.com/fo...-installed.html

They will not remove our restriction.

Ask Scott when you see him next how well it worked in that regard.

snapback.pngbigkevracer, on 27 April 2011 - 02:13 PM, said:

If I read the old discussions properly though, Mines wouldn't remove the throttle restriction.

I figure we're not going to get a flash that does everything we want, but a flash that removes the speed limiter and throttle restriction and gives us 80-90% of what we want is fine with me. And when I want that remaining 10-20%, I can get an emanage knowing that the two main areas it can't fix are sorted from the flash.

Mines completely remap the entire throttle map... does that mean they remove the restriction? Buggered if I know.

I asked them directly if they remove the restriction below 3000rpm and they replied "we do not", but they did state that they do remap the entire throttle map up to their normal 7100rpm (they will go higher, but issue a warning of "please consider engine safety").

I think your plan of the Gzone + emanage is almost as good as it gets.

came across this whilst searching ebay for other stuff.................... thoughts ???

Throttle Controller

Yes, a waste of money IMO. You'd be better off spending the $350 on real mods to improve the throttle response. Did you see the claim:

Enhances throttle response OR fuel saving of up to 20% ? I suppose 2% is 'up to 20%'....

Edited by Commsman

new o2 sensor today

was hoping to pull the pins out of the old plug and swap it over, turns out the neo plug has slightly smaller pins :(

3 crimp joiners later and i was away, i think the old sensor was ok but for ~$70 it should help on the way back up to qld

also half way through waxing it, so its slippery through the air ninja.gif

Installed my Walbro 250 pump in my M35 today and set up a power source direct from the battery to ensure full power to the pump at all times.

Reason for changing the pump was following the introduction of Nismo ECU, 3 inch suction pipe and spring on turbo actuator was seeing AFR being too high.

AFR's on medium throttle and below 4500rpm were all good and around 11.8-12.5 but higher rpm and more throttle saw AFR's is 13's.

So new pump fitted and now AFR's are much better at 10.7 to redline.

Now to start playing with boost again to see what the car will handle.

:rolleyes:

Installed my Walbro 250 pump in my M35 today and set up a power source direct from the battery to ensure full power to the pump at all times.

Reason for changing the pump was following the introduction of Nismo ECU, 3 inch suction pipe and spring on turbo actuator was seeing AFR being too high.

AFR's on medium throttle and below 4500rpm were all good and around 11.8-12.5 but higher rpm and more throttle saw AFR's is 13's.

So new pump fitted and now AFR's are much better at 10.7 to redline.

Now to start playing with boost again to see what the car will handle.

:rolleyes:

Hey Andy, that's a big change. Are the AFR's that rich throughout, or mainly heading towards redline?

Hey Andy, that's a big change. Are the AFR's that rich throughout, or mainly heading towards redline?

Have to do a bit more testing to be sure but I don't think they were. Will be able to tell you more tomorrow.

Also got to get the boost controller working again and run more like 17psi.

Have to do a bit more testing to be sure but I don't think they were. Will be able to tell you more tomorrow.

Also got to get the boost controller working again and run more like 17psi.

Nice result & keen to hear what the AFRs are like after running around for a while. Mmm, more boost :thumbsup:

Hey Andy, that's a big change. Are the AFR's that rich throughout, or mainly heading towards redline?

AFR's are

off boost low RPM (0-2500) 13.5 - 14.5

Low boost mid RPM (2500-4500, up to 10psi) 12.3-12.8

High boost full throttle (4500 +, 15psi) 10.7-11.2

Quite happy with these numbers.

Andy, those AFR numbers are pretty darn good. Off boost & mid range is very close to what I'm running. Upper end of rev range / max boost is a little rich compared to what I found works best for my car, so you have a nice buffer to increase boost safely.

Did you get a look at max injector duty cycle now?

Did you get a look at max injector duty cycle now?

I knew someone would ask that...... lol

It is certainly better than on the stock pump but at redline I am getting up to 95% duty cycle but this is with AFR of 10.5 so not too worried about that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...