Jump to content
SAU Community

Recommended Posts

Now your talking scotty one set for street and the other for track ;). Just dont tell the missus!!

I was still surprised as they pulled me up pretty well for most of the 3 laps just had to brake alittle earlier as i wasnt super confident with them and im no expert on the track as it was my first time at a real track.. Good day out and surprised a shit load of people as im the loan wolf at the moment in tuned stags over here.

Replaced shocks all round, and bled the callipers since i was there.

Also - HPX are hopeless for track work. I know two people who tried tand both were miserable failures.... A1RMs are a whole different story, but i would expect they would be tough on rotors if you used them for street. Cold bite is not great either, so agree that pads are the #1 thing to swap in and out for track days (or maybe #2 after tyres).

I've actually heard that if used hot they are good on rotors

Street work (cold) is what kills the rotors with the ar1m's

18 x 9.5 +22 Volk Rays Gram Lights 57DR in black

235/35/18 Federal 595 RSR's

GK Tech V2 adjustable Rear Camber & Toe Arms

'93 R32 GTR Pull type gearbox

Extreme cushion button clutch (installed by Kidafa, thanks kid!)

Nismo GT Gear Knob

Greddy Informometer

Pioneer DEX-P99RS

JL Audio C5 6.5" Splits

Series 3 R33 GT-R seats

Greddy catch can w/ speedflow lines & fittings

Setrab oil cooler w/ speedflow lines & fittings

New Nissan Thermostat

Radiator flushed

AM Performance low mount manifold

AM Performance split dump

Garrett GT3076R w/ speedflow lines & fittings

Tial 44mm external Wastegate

Splitfires

Deatschwerk 1000cc injectors

Walbro e85 fuel pump

E85 tune

Ran 290rwkw on the heartbreaker dyno...

Now more serious, new build 50% complete:

Tomei Rods

Tomei Pistons

Tomei Oil Pump

Tomei Sump Baffle

N1 Water Pump

Ross Harmonic Balancer

Deck Shaved

Head fully reco'd

Oil control mods

Supertech Valve Springs and Titanium Retainers

Tomei 256 Poncams

ID1000 injectors with fuel rail and Turbosmart ext. Fuel pressure regulator

Still e85 of course :D

I think that's it, I'll update with the dyno sheet when it's all done... :)

Excellent ! Well done what psi you running , sounds like time for some photos to come up, and start sourcing a rs4s rear cradle ;) axles go snap soon

Excellent ! Well done what psi you running , sounds like time for some photos to come up, and start sourcing a rs4s rear cradle ;) axles go snap soon

I'll be aiming for over 20 once the build is finished, I'm guessing 22ish, or wherever the 3076r runs out of efficiency really. I'm hoping it will be finished in 5 weeks, still waiting on the jun extended crank collar for the Tomei pump. Pistons/rods are going in as we speak and I'm pretty sure the head will be finished by now... I'm going in to check on progress next week when I get home, I'll take some pictures and report back then :)

At what power level do the rear axles become questionable?

I'll be aiming for over 20 once the build is finished, I'm guessing 22ish, or wherever the 3076r runs out of efficiency really. I'm hoping it will be finished in 5 weeks, still waiting on the jun extended crank collar for the Tomei pump. Pistons/rods are going in as we speak and I'm pretty sure the head will be finished by now... I'm going in to check on progress next week when I get home, I'll take some pictures and report back then :)

At what power level do the rear axles become questionable?

Impressive specifications! (should have got the crank collar from me though...ahem). I guess you will be looking for around 350awkw? Your skinny tyres (would be illegal over here) might save you but I would be looking to upgrade especially if you are going to drag it.

What brand is the rad; looks huge! I take it that it sits a bit too far back to fit the shroud?

Im not sure what brand it is but its 3 times as thick as the old one! had to get one hacked up to fit in, yep fan just clears the rad by about and inch or so

very nice suction pipe!

P.S. Without the fan shroud I suggest you do some shielding in front of the pod to get rid of the hot air.....remember the heat sensor is in our AFM and it will affect your power through traffic.

Thanks its a bit of mix of scottys one, the shielding sounds like a good idea ill look into it at some stage

Impressive specifications! (should have got the crank collar from me though...ahem). I guess you will be looking for around 350awkw? Your skinny tyres (would be illegal over here) might save you but I would be looking to upgrade especially if you are going to drag it.

He he, I didn't even know you sold them :P I got the jun one through Jesse, it cost around aud$100 so I was happy with that :)

The federal 595rsrs are known to fit wider, more like 245... but if I have to upgrade then so be it :D I'll probably have to look out for one now...

I'd be happy with anything over 330wkw really, I'm not that crazy for power and not yet willing to upgrade the turbo again so we'll just max out the 3076 and I'll be happy... for now :)

235/35/18 Federals on 18x9.5 +22 gram lights :)

Very nice :)

My axles held up well on the street but first second they saw a the track with vht on it snap!!! Just finished putting in rs4s rear cradle with a 2way in it . 350 is a good aim After that your leaning hard on the drive line but not so bad in an auto , was going to pushy old girl a fair bit harder put the built motor in do a dog box change turbo push towards high 400s ,basically it's like starting again lol . But I thought I've already reached my set goal and haven't turned boost up yet or my wmi on . So might buy another toy instead ;)

What size rear you running on 3076r

Scotty do you think I should change pads for track work or will the stock akebono's pads be suffice ?

It depends how much you lean on the brakes, and how hot they get. I would assume you would need A1RM's at a minimum.

235/35/18 Federals on 18x9.5 +22 gram lights :)

Very nice :)

My axles held up well on the street but first second they saw a the track with vht on it snap!!! Just finished putting in rs4s rear cradle with a 2way in it . 350 is a good aim After that your leaning hard on the drive line but not so bad in an auto , was going to pushy old girl a fair bit harder put the built motor in do a dog box change turbo push towards high 400s ,basically it's like starting again lol . But I thought I've already reached my set goal and haven't turned boost up yet or my wmi on . So might buy another toy instead ;)

What size rear you running on 3076r

Very nice :)

My axles held up well on the street but first second they saw a the track with vht on it snap!!! Just finished putting in rs4s rear cradle with a 2way in it . 350 is a good aim After that your leaning hard on the drive line but not so bad in an auto , was going to pushy old girl a fair bit harder put the built motor in do a dog box change turbo push towards high 400s ,basically it's like starting again lol . But I thought I've already reached my set goal and haven't turned boost up yet or my wmi on . So might buy another toy instead ;)

What size rear you running on 3076r

It's a 0.82 rear. There are a few little things left to do to it, but like you I don't feel the need to spend much more from here :)

57DR in the box...

post-36265-0-07202400-1380585773_thumb.png

What's the response like with the .82 I would like to compare with mine out of interest :)

I'll get the dyno sheet and post it up when I'm home, I didn't drive it in that iteration of the build :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...