Jump to content
SAU Community

Recommended Posts

Added to the Steady growing stock pile

Purchased a 2nd hand Turbo via import Monster for a high flow upgrade, to prepare for the inevitable ceramic wheel failure.... (78000kms current)

Purchased the new Greddy Profec boost controller threw just jap (its been annoying watching the gauge and feeling the factory boost settings dropping of back to 7-9psi.)

Looking forward to installing all at once

Oil and filter this weekend, first car I have owned in which i changed oil on time instead of kays.

Used to doing 30+k a year, new job, new (old) car which wifey & young daughter get shaken up and now I'll be lucky if a crack 10k a year.

On the down side, found a ruined drivers inner CV boot and probably a dead breather in the gbox, I have a smurf bood dribble down the box...

Explains the gearbox oil smell after it gets a few revs.

Pain in the A though.

Added to the Steady growing stock pilePurchased a 2nd hand Turbo via import Monster for a high flow upgrade, to prepare for the inevitable ceramic wheel failure.... (78000kms current)Purchased the new Greddy Profec boost controller threw just jap (its been annoying watching the gauge and feeling the factory boost settings dropping of back to 7-9psi.)Looking forward to installing all at once

Nice! If you dont mind me asking - how much did the turbo set you back?

I installed my aux cable to the TV tuner on the weekend and replaced a few cracked vac hoses - not much, but its something!

Edited by Dmyze_

The last Hypergear turbo took a month, as Tao was in China. It's a very good idea if you can get one, although you will never get that sort of money back for them over here, not unless they are running perfectly.

Perhaps I can loan my spare out for a small fee? I would love to have a highflow on the shelf to help customers out, but I can't justify having $1300 tied up in a turbo sitting in the garage.

The Nm35 2nd hand turbo was $437.50 thats delivered to my place inclusive...

Today

Purchased Blitz catback exhaust...

Purchased R34 GTT RDC brand replacement cross drilled dimpled, slotted front rotors ill get the new callipers once I do a bit more research & bargain hunting...

roof racks mounted, rear cargo net also put on, not sure what it's supposed to mount down to, so just have it hanging from the room like a net

hopefully put the suspension in over the week, have so much to do :(

I fitted my replacement headlight in my sII and the light is poiting waaay to far down, tried to adjust it up with the screw and the electric adjustemnt fights me and just moves it back down...am i missing something here on how to adjust it up?

I fitted my replacement headlight in my sII and the light is poiting waaay to far down, tried to adjust it up with the screw and the electric adjustemnt fights me and just moves it back down...am i missing something here on how to adjust it up?

make sure that the globe is sitting correctly into the fiting it might be sitting up on one of the tabs

My mechanic relearned the throttle body. What a missiin that was. No body touch your throttle body (besides craig). I was unaware before and now after going through the mishap wouldnt recommend it to anyone. On a lighter not received the oem hids that I will be installing this week.

My mechanic relearned the throttle body. What a missiin that was. No body touch your throttle body (besides craig). I was unaware before and now after going through the mishap wouldnt recommend it to anyone. On a lighter not received the oem hids that I will be installing this week.

It is a bit of an epic if you don't get the timing of each step right, but a bit of practice gets it done.

You'll like the HID's. ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...