Jump to content
SAU Community

6Boost Rb26Dettt Manifold Install

BoostdR

By BoostdR,
in Engines & Forced Induction

 Share

Recommended Posts

BoostdR Mentor

BoostdR

Posted
Posted

I have pulled my motor out to install some 6Boost Manifolds. I have found some issue's, most expected.

-OEM water and boost hard pipes that run beside the rocker cover don't fit

-OEM twin turbo pipe doesn't fit. I have a hard pipe kit here and will update you all if it works

-Manifolds aren't even. 4mm out. If I hold one up and then tighten I can get it down to 2mm. Not to bad but I hope my Front pipe fits ok

-Both manifolds just foul on the head. I will have to grind the head tabs down as I also need the clearance for heat wrap

There is no doubt these will make more power with better spool over my stainless items. I will be on the dyno to confirm

Matt

Pictures tell the story:

4cf66aa9.jpg

c9b4e905.jpg

8200f9fa.jpg

4d1a93cf.jpg

Link to comment
https://www.sau.com.au/forums/topic/355887-6boost-rb26dettt-manifold-install/
Share on other sites
  • Replies 161
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Diameter wise - whats the internal of the pipe?

Just thinking if it's actually larger, will it hinder perhaps due to lower velocity etc?

The runners are certainly longer ye?

Be interesting to see results. Certainly a pain RE: OEM piping/lines, but given the length of the runners that would be unavoidable regardless

BoostdR Mentor

BoostdR

Posted
  • Author
Posted (edited)

Diameter wise - whats the internal of the pipe?

Just thinking if it's actually larger, will it hinder perhaps due to lower velocity etc?

The runners are certainly longer ye?

Be interesting to see results. Certainly a pain RE: OEM piping/lines, but given the length of the runners that would be unavoidable regardless

The OD is ~42.5 same as my stainless mani's

The also are ~1.7times longer

Any gain will be amplified at my power levels so we should be able to see and get a accurate % for others to make a eductated decision if the install hastle and cost is worth the effort

Edited by BoostdR
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

Indeed, will be good to see.

1.7x longer is interesting.

Dyno might not show difference when loaded up in terms of response, you'll have to get some seat of pants action going :D

Pics of old manifold by chance?

BoostdR Mentor

BoostdR

Posted
  • Author
Posted

Indeed, will be good to see.

1.7x longer is interesting.

Dyno might not show difference when loaded up in terms of response, you'll have to get some seat of pants action going :D

Pics of old manifold by chance?

e1312463.jpg

dorifticon Community Regular

dorifticon

Posted
Posted

Wow didn't even know these existed. Can I ask:

1) Any dummy fitment done to see how these clear the strut towers etc?

2) the collector pipe - does it not fit by a little or is it just a completely different thing? ie is the hard pipe setup roughly similar in configuration to the OEM stuff, just some minor changes, or totally different? Just wondering if it's achievable for the DIYer (most of my inlet is now custom).

3) sorry if it's mentioned elsewhere, but what are the turbos?

4) is it intended that the mounting position of the turbos would enable the OEM y-pipe to connect up to the dumps? Or is completely different setup required?

BoostdR Mentor

BoostdR

Posted
  • Author
Posted

1. clearance to the strut towers not an issue

2. No chance of fitting the twin turbo pipe. The hard pipe kit I have routes differently to the OEM..away from the rocker cover

3. GTRS

4. Front pipe is meant to be a direct fitment

post-49288-0-77962600-1299210203_thumb.jpg

J'z-R33 Grand Master

J'z-R33

Posted
Posted

You will need to modify your aftermarket 'twin turbo' pipe. The rear will foul the front manifold.

Front pipe will bolt in, no dramas there.

I had an issue with the stock rear o2 sensor fouling. That may have been due to the aftermarket dump pipes though.

Cheers,

Johno

BoostdR Mentor

BoostdR

Posted
  • Author
Posted

how do you get 4mm out? if so your front pipe will be 4mm out to... in wghat dimention are they 4mm differant?

The turbo flange level (height) when mounted is 4mm different. One is higher than the other.

BoostdR Mentor

BoostdR

Posted
  • Author
Posted

Update

I have ground about 2mm off my head tabs, now has enough clearance for the manifolds with heat wrap.

The manifold flanges are also threaded, why I don't know. They will have to drilled out to allow the turbo studs to poke through.

I have ordered some black braided stainless line and AN fittings for the water lines. I have also found a -6AN To 3/8 barb to join at the back of the Plenum. I will post up my order list soon.

Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...