Jump to content
SAU Community

Recommended Posts

  • Replies 436
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

There are ways around this... you could break the beam (and start the timers) then take off and see what MPH you can get. This can indicate your potential ET on a perfect run. Or you could take off easy and then plant it - again, to see what MPH is acheived on the run, and hence what potential ET the car is capable of.

Alternatively, you could take off hard and then either back off or brake before the finish line. Couple the first half track passes with the MPH acheived on the other runs and you can work out the opotimal run ET and TS. Then, go hard at the end of the day and get your 10second timeslip and get booted :D

/waves@Aaron :D:action-smiley-069::whistling:

That must have been quite a while ago and WSID's private days were much different back then. Now they have two types, ones like this SAU:NSW one (ie 11.00+ cars), and the private track hire days for ANDRA-teched cars (a handful of cars only).

Is there truth to the rumor that if it's blatantly obvious by your 60" foot that you're holding off that you can get booted by that time even if you don't run a 10?

Is there truth to the rumor that if it's blatantly obvious by your 60" foot that you're holding off that you can get booted by that time even if you don't run a 10?

The rule book does allow it, but it only gets used if you are being an idiot or a c*nt towards the officials etc.

Is there truth to the rumor that if it's blatantly obvious by your 60" foot that you're holding off that you can get booted by that time even if you don't run a 10?

just looked through the ANDRA rule book and can't see anything about 60" but there is a time limit of 7secs for the 1/8th mile

I was just reading in the previous event (2007) where several cars ran within 5 or 7 hundreths of breaking into 10's and was fine. So sounds like it isn't a "fuzzy" rule, but I guess one of the guys that is closer to the rules could answer definitively.

List is all updated to date.. Come on everyone, you wanted it and said u would come and now you have all dropped off..

Tell your friends and get entered because if you dont do it now it may never come back!

There is nothing about a short time to get you booted, just ET or trap speed.

You can also be booted if you are running quicker than 12.50 and have slicks without front runners. I did this in testing and sandbagged at half track .. and got booted.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...