Jump to content
SAU Community

Recommended Posts

Mate just got a major defect pulling out of the panel shop. Didn't directly take a speed, and was going over it on angle and the cops pulled him up about 10 seconds later.

Got done for being too low, tint, walls, bump stops and tyre placard. Merry Christmas.

let me know if u want aircon, i can get volume builder prices.. quote for my alarm from RACV was $600 more with 2 less sensors.. from another alarm place was $200 extra and 2 less sensors as well :\

Yes please Kaz! What's brands can you get? I have nfi about air-con brands and quality so will have to do some research :D

Primus back in the 90's. Always a huge queue waiting for dialup technical support.

On the current topic so far very happy with the two Panasonic split systems I had installed a couple of months back.

Aircon will cost me $3k + install, which shouldn't be much with my mate doing the electrical and his mate doing the plumbing

Bike would cost me $250+$250 in licensing, then $4-5k for the bike, $250ish in rego, $1k-ish in gear

Would be out riding it and wouldn't need the aircon on...

hmmmmmm

Need both

Dam its hard to get off the line with my new car :domokun: Needs a tune so when I light them up off the line I can recover and overtake ;)

f**k me the ZF auto in performance mode is quick shifter though, pretty impressive.

Dezz bike is good fun, good to just get away from everything and take some "me" time. No phone, no radio, no stressing about work. It clears your head. And then you've got the adrenaline pumping if you want to go a little silly.

Dam its hard to get off the line with my new car :domokun: Needs a tune so when I light them up off the line I can recover and overtake ;)

f**k me the ZF auto in performance mode is quick shifter though, pretty impressive.

Dezz bike is good fun, good to just get away from everything and take some "me" time. No phone, no radio, no stressing about work. It clears your head. And then you've got the adrenaline pumping if you want to go a little silly.

people are gonna tell you auto is gay.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...