Jump to content
SAU Community

Recommended Posts

went to exhaust place today to get some pipe for intake, they noticed i had a factory system still on (is factory but decat with varex copy twin tip) but because he recognized my old man (did exhaust for his merc) he asked me if I wanted to get a full 3" turbo back system with hi-flow cat made up and installed for $1k as "mates rates". This good deal? :laugh:

lol mates rates...my turbo back 3" was $600 with me supplying the cat and varex end muffler. Mild steel with mandrel bends. Don't bother with stainless it looks like ass after a year anyway and mild steel sounds better :P

It wont work with larger injectors.

You'll need to configure them within the PFC at a bare minimum regardless, or it will just over fuel and stall, it might not even idle.

This Birdy. It's a piece of piss to do, should be in Paul's faq

lol mates rates...my turbo back 3" was $600 with me supplying the cat and varex end muffler. Mild steel with mandrel bends. Don't bother with stainless it looks like ass after a year anyway and mild steel sounds better :P

really? how does surface rust look better :P

fml. did Rev210's 5min $5 intake pipe mod and i just took my car for a little drive and it drove like shit. held boost fine but didnt go. before mod it went fine. HELP!!!!!

took off ic piping from turbo and return flow to get better access to rubber induction pipe, unplugged and took out afm and pod, cut induction pipe and inserted 3inch diameter/12cm long mild steel pipe, placed piece of pipe that was cut off back on and both side are secured with metal hose clamps, plugged in and insterted afm and pod back on, put ic piping back on.

Just some extra info: battery was disconnected when this was undertaken, Rev210 says to remove whole induction pipe but i left it in because the clamp for the plumb back recirc pipe was impossible to get off so i cut it while it was in the engine bay.

**EDIT**

Link to Rev210's guide.

http://www.skylinesaustralia.com/forums/topic/173019-rev210s-5min-5-intake-pipe-mod-for-your-stageaskyline/page__mode__threaded__pid__4756582

Edited by JDMKiD__/ⓞⓞ-33

Any wastelanders going to the photoshoot meet/cruise tonight?

I might head down for a bit

just around the corner from my house saw mr.P pulling over some Mitsubishi and searching his car! His partner greesed me off as i drove past. Afraid to leave house with 32 now haha

I was thinking of going down and getting some photos.... dunno if i can be bothered though... dunno anyone whose going down either really...

Got to start somewhere. I'm sure many a people didn't know anyone at their first meet

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Nah. Was just wondering if you were having a small stroke or if there was some slur/gaf/inside joke that I wasn't aware of.
    • That was a fark up, it's Salamanca Place I was thinking of. And now I'm curious as to what potential slur/gaf I have caused with Salamander Road, ha ha!
    • Actually everyone on the roads was really well behaved. The only person that did any minor tailgating was a local hoon in a Turbo Focus. Unfortunately we weren't going the same way so there was no grand initial D touge battle. Lots of people pulled over and let me through. The amount of "Hey man nice car, omg skyline, nice 34 man woo" was suprising. Like really suprising. Like almost annoying. My partner was obviously surprised, she'd never seen anyone in the real world point out the car/like the car/want to chat about the car before, so to have like 3 people per day mention it was notable, I could finally say SEE? SOMEONE THINKS THEY'RE COOL. Everyone was also pretty suprised about the weather. Every day was dry and about ~13-14C. Mount Wellington had a sign that said they close the gates at 9pm and I was heading up there at about ~7:30. It was VERY apparent that conditions were getting significantly worse by the minute on the way up and down. The road on the mountain was terrible though, it's no driving road. I have various suspension related questions now. Luckily it was only about 20 minutes from where we were staying to the top of the mountain as said Google maps. We only had the 2 nights in Hobart. We went to the Farm Gate Market though which was really good - And went down to the Hastings Thermal springs/caves down there during the day. I'd definitely be up for going back again, so luckily there's a few more sights yet to see. Didn't get to do the west coast/queenstown/cradle mountain so this was supposed to be a 'scouting' trip anyway of sorts if I were to one day do/take part in/organize a more car-focused trip. As for the boat, it wasn't bad. Well it was bad, but not in the way you're thinking. We did the night trip which leaves at 6:45 (though you have to be there ~2 hours earlier) and arrives the next morning at about 6am. There is nothing to do on the ship. If you plan accordingly and bring a book/tablet/show to watch/charger you can just chill out, take some Travacalm and just sleep through it. The food there is an extremely basic buffet that costs $32 a plate, or $14 for a $3 pizza. The way back we had a travel kettle and a few different types of cup noodles and made our own tea/coffee in the room. This was a far superior way to do it. At the very least book one of the rooms with beds. I guess as we were in the off season we didn't have room mates. You get an option for rooms with 4 beds (2x bunks) or a room with just the two bottom beds. There's also some option for a deluxe queen bed but it's much pricer. We've been on sleeper trains in Asia before so we figured this is similar (and it was)
    • You just gotta be really, really, really clear and decisive with what you want your end product to be. 99% of people who want this conversion aren't "I want to run a 295 front tyre!" so they don't really need the widebody. They just want the OEM body to look a little less dumpy, so bonnet, bar, skirts job done with some camber, stretch, slam. It's when you want that, but then decide to pivot later you get big problems. See also if you're willing to get an all in one fibreglass bar, and you're willing to accept fibreglass problems like cracking the entire item on a driveway, instead of just a piece attached to the bottom, etc etc etc. Decide this all before buyin'.
×
×
  • Create New...