Jump to content
SAU Community

Recommended Posts

Fk going to these places, my tailor flies into Melbourne, takes measurements, goes back to Malaysia and sends the suits back over.

Higher number doesn't always mean better quality, just refers to fineness of the thread. There are plenty of 130 suits that are better quality than super 150, they'll also wear better. If you have a job with a lot of moving around, you don't want to be rocking super 150...feels great and light, but you'll wear it out in no time. I tend to save that grade for special occasion suits, weddings etc.

/suitlinesaustralia

This guy knows.

Didn't buy suits for daily use so should be fine. Got 2nd pair of trousers too incase of any wear.

Pfft what? As if you like getting dressed up? It would be ok if I didn't have to do it everyday. But fk it's annoying, I look forward to getting home and getting out of these clothes

I like wearing a suit...but I don't have to everyday, so it's a bit more special that way.

Also, have you had a proper tailored suit made up for you Aaron? Cause there's a huge diff in comfort between off the shelf and made to fit.

This guy knows.

Didn't buy suits for daily use so should be fine. Got 2nd pair of trousers too incase of any wear.

2nd pair of trousers always a good idea

I've ripped the pants on almost every suit I've owned :/

I like wearing a suit...but I don't have to everyday, so it's a bit more special that way.

Also, have you had a proper tailored suit made up for you Aaron? Cause there's a huge diff in comfort between off the shelf and made to fit.

Could be right, never really bought a tailored suit, but never really felt like I needed to. Al is right you do get treated differently, even in business shirt And slacks, but I just don't like them. I wear the work vest over the shirt for work just because I hate it that much.

Perhaps my opinion would differ if I had a gym body lol. Dunno..

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...