Jump to content
SAU Community

Recommended Posts

I broke a Kinchrome 3/8" ratchet and breaker with jack handle over the end trying to undo different rears. If you have a 1/2" socket and breaker it'll do it a lot easier than the smaller stuff.

My breaker is a 1/2" but my sockets are 3/8", used an adapated to fit the 3/8" sockets.

Time to upgrade to proper better tools i suppose...

lol Mohson, that's not cool!

So is that how the stanceworks crew mod there cars? hahah jk

I bought a breaker bar earlier today, thanks though Martin. Will definitely keep you in mind though!

DIY chaning coilovers, it'll be fun they said.

Next minute, socket piece slit almost in half. ..... that thing is crap tight!

So right now, I've only got my left rear coilover in. Car sits like it's got crooked legs or something.

Back to bunnings to buy a new socket piece dammit.

Hahah. Yeah technically it's not a big job, but when you don't have the right tools, it can be pretty annoying! I think I couldn't find a 12 (or something or another) for the life of me, and I needed it at one stage when taking out the rear seats, and was just like... Well, feck. But luckily my mate had tools :P.

How much was shipping to aus?

$20 (international express). So all up, still cheaper than HN by far. $419 all up. Very good value proposition. Ideally could have gotten a bumper or charging orb if only they were in stock / available, as it's a flat shipping fee.

If I bought one now. would they have stock, and how often does stock come. Cause i remember there being a huge backorder for it.

They appear to have stock under control now, considering after selling out again last Thursday, they're back in stock less than a week later, today. Noting it says expect 2-3 weeks for delivery. But that's just google underpromising, just in case something happens (considering how quickly people are receiving their phones).

we used the blowtorch from my kitchen LOL

Please explain why did you had to use blowtorch to undo the bolts on your coilovers?

I think you've told me why but for the life of me I can't remember why.

heat makes metal expand, then when it cools it contracts a tiny bit and it breaks free.

just dont do it with an industrial blow torch directly on the CAS to remove it without asking the customer then tell them they will probably need a new crank when they pick it up like a certain workshop did to a member here

Cheap/wrong tools cost more in the end.

when you have to replace them/the bits you broke multiple times false economy.

buy them one and buy them right, and get the correct tool for the job.

The amount of cheap tools I've gone through...

Sidchrome set has not failed once in the now 2 years of having it

Cheap/wrong tools cost more in the end.

when you have to replace them/the bits you broke multiple times false economy.

buy them one and buy them right, and get the correct tool for the job.

Links to a decent tool set that has everything? I might make a start to pull apart my engine whilst its sitting in my garage

I had some cheap tools that served me good for a while, but thief decided to help himself to my tool set.

Links to a decent tool set that has everything? I might make a start to pull apart my engine whilst its sitting in my garage

I had some cheap tools that served me good for a while, but thief decided to help himself to my tool set.

cheap set of tools that have everything:

456x330.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
    • No, you're wrong, and you've always been wrong about this. The Nismo has 2 sets of openings. One is a real 2-way, and the other is a 1-way. There is no 1.5-way possible with the ramps that they offer. A real 1.5-way does exist. That Cusco stuff I posted is a prime example. If the forward drive ramps are, say 55°, and the overrun ramps are, say, 30°, then you will get about half as much LSD effect on overrun than you do on drive. It is real, it realy works. OK, you're slightly right. The Nismo has 55° and 45° ramps on the 2-way, so it does offer less LSD effect on overrun. But, I think that just means that they've (probably) sensibly established that you do not want actually equal LSD effect on overrun. You just want "quite a lot, but not quite as much as the drive LSD effect".
    • Just wanted to unearth this and post my baby with the new front ❤️😝 Took her to my wedding rehearsal today. Next up is getting wide skirts (after wedding)
×
×
  • Create New...