Jump to content
SAU Community

Recommended Posts

what's RMIT?

University

Tis a lot easier to get a new job when you already have one than when you don't

Wasn't the case when I tried looking for replacement job before I left Coles.

Not really... He wasn't given the opportunity, he bought it...

He owned DC and was essentially self sponsered to get to where he is today... so unless I start a multi billion dollar fashion label, I can't see it eventuating :P

just start a company like Illest. get some tshirts made using an underated MS Word font and print them in 2 different colours. then get some lanyards made up, a bazillion stickers to give away and suddnely people will pay money for that. cause its cool. and you are personally adding style and fashion to the car scene.

Kinda like MIT

Basti got banned last year for counting cards at Crown Casino.

Made about $250k cash before they kicked him out

RMITafe brah ;)

A maths lecturer I had back in the day legitimately was booted for counting cards lol

Understand where Grant is coming from...sometimes you get too comfy in a job and need to quit, else you'll never be motivated enough to search hard for one.

So no 300km needed? Figure 8s for 30 minutes and that's it? (Where the fark in the Eastern Suburbs can you do figure 8's in a skyline for 30 minutes without 4 HWP cars and Rapid Response Units showing up?)

Any particular kind of oil for run in and also afterwards?

Figure 8's lyk dis?

I went to Supagas on Mountain Highway in the after hours for my KAAZ run in...had a security car turn up, that's about it. When they can see you're not leaving rubber marks behind or making ridiculous noise, they're a bit more understanding!

Figure 8s like drawing figure 8s...can't think of any other way to explain it. Or you can draw the ABC symbol...

Start off just steering, then as the diff starts to break in / shudder less often, you can add some throttle in the turns to induce break away under acceleration.

Understand where Grant is coming from...sometimes you get too comfy in a job and need to quit, else you'll never be motivated enough to search hard for one.

One thing that I don't understand that is they advertise like they need a worker urgently and when I contact them, they suddenly decide that they don't need one urgently. Happened to me 4 times today.

What's up with that?

One thing that I don't understand that is they advertise like they need a worker urgently and when I contact them, they suddenly decide that they don't need one urgently. Happened to me 4 times today.

What's up with that?

Discrimination

Again, not fussed whether it's P/T or F/T.

Just want a job, simple as.

I'm in a similar boat as you Grant, jobless until my engineering kicks off which is unknown atm.... zzzzz

Have you tried looking at gumtree? Some odd jobs here and there on that site.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...