Jump to content
SAU Community

Recommended Posts

2 door is good excuse to watch dem struggle in mini-skirts.

and 2 door is harder to escape while car is moving, you know incase they do a runner.

Good thinking

Keep in mind that Leigh's engine came with a factory 335 flywheel kw and the current HSVs have 325 in stock form. If Holden put out a blown V8 it'll be above the FPV power figure cause that's what those two companies do.

In the end what's gonna matter is displacement and power handling potential...if they use LS9, it's a supercharged 6.2L engine > supercharged 5 litre. Coyote is a great engine, but there's nothing particularly trick about it...all supercharged engines respond well to pulley upgrades and tunes.

It would be interesting to see the price though; if they spread across the range or save it for the GTS.

Gee fair whack on your first outlap.

Looked really slippery? Oil spill there previously?

Aaron. We barely half way through. If u come now. Still tonnes of food!<br /><br />And there is no guinnea cops now!!!!<br /><br />Good wine hurr too. <br /><br />We just doing stuff bit by bit.

Lol mad invite!

pVEka_bb_original.jpg

Come past one night brahz! Take me for a spin uleh

Pretty sure HSV stated it won't be the LS9, and if it were yeah they're awesome but expect to pay 100k+ for the car lol

Also the ford modular engine is complex, much more than the pushrod single cam chevvy 6.2lts, I'm talking n/a vs n/a here 5lt vs 6.2 and 6.4 ftw

The 5.0 L (4951 cc, 302 cid)[12] "Coyote" V8 is the latest evolution of the Modular engine.[13] Ford engineers needed to design a V8, specifically for the Mustang GT, that would compete with the GM 6.2L LS3 used in the new Chevrolet Camaro, and the new Chrysler 6.4L Hemi ESF in the Charger and Challenger.

Edited by UNR33L

Keep in mind that Leigh's engine came with a factory 335 flywheel kw and the current HSVs have 325 in stock form. If Holden put out a blown V8 it'll be above the FPV power figure cause that's what those two companies do.

In the end what's gonna matter is displacement and power handling potential...if they use LS9, it's a supercharged 6.2L engine > supercharged 5 litre. Coyote is a great engine, but there's nothing particularly trick about it...all supercharged engines respond well to pulley upgrades and tunes.

It would be interesting to see the price though; if they spread across the range or save it for the GTS.

ford and holden both have to keep each-other in check with stock power figures, also the supercar scare shit will return if they go nuts.

Ls9 has displacement and that is all and with 1.2L still isn't as efficient uses more fuel and needs more mods to be on par with a 5.0 on same boost levels.

power handling potential? on stock blower 5.0 coyote many people have made 480-510rwkw stock engine zorst pulley intercooler tune e85 intake.

ls9 will need heads cam, zorst intake pulleys e85 larger heat ex-changer(internal plenum cooler and external radiator)

keep in mind here the 5.0 coyote has a 1.9l blower and the ls9 has a 2.3l

imo stupid debate anyway, FKN v8 MATE

@ hamish, does the sous vide in the esky hold 59 degrees for the entire hour? or is there a temperature drop?

I'd normally prefer to sear after i sv though. so i'd be concerned about temp drop when i put in the meat.

my esky drops approx .5 - 1 deg per hour so not really...

you can sear afterwards, works the same, as you are not putting enough cold meat in to drop the temp of all that water.

I have done both ways, however sealing first works better for sous vide as the flavour of the searing penetrates the meat.

even in professional kitchens with propper vaccuum sealers and circulators I seal the meat first

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...