Jump to content
SAU Community

Recommended Posts

I have the HD hero and it fits; pretty sure it's a GoPro 1

ok looked it up

so the first of the gopro as we know it was acautlly the gopro Hero 5, SD ran on AAA batteries and 2gig card only,

This was my first one so guess that why I call it the first gen,

then the Hero 960 a higher res version

then they dropped the numbers and started calling them.

HeroHD,

HeroHD2

HeroHD3

go figure.

My R33 GTRST made it to work this morning :D It's around the corner getting an alignment as we speak.

Now, who can remember the Bedding in instructions for a newly rebuilt 1.5way with Nismo discs... Hamish?

I need to go and do 30 minutes of slow figure 8's in an empty carpark somewhere that police aren't going to show up and defect me for "doing hektic skids"... This will flatten and bed in the plates in the lsd center by moving/grinding them back and forth against each other.

Keep speeds down (like try to stay under 60 or so) for the next 1000km? This one is going to be tricky since its a daily (but I can take mainly 60 zones to get to work and back)

Not bad job...

Pretty happy. Roof bonnet boot was all white and faded from oxidation.

Yet to see car in sunlight

5y6a4u9a.jpg

upy3y7uj.jpg

nice...that red always does that...its a shocker...but gives good results when polished up :thumbsup:

so what machine did you buy ?

This is the car that killed my buff the other day...time for a new one...

blacjak3_zps236ae712.png

<br />nice...that red always does that...its a shocker...but gives good results when polished up :thumbsup:<br />so what machine did you buy ?<br /><br />This is the car that killed my buff the other day...time for a new one...<br />

Bought das6 pro. Man this shit takes a lot longer than a rotary. At work I could have finished this car in 3 hours. <br /><br />Took 9 hours instead. But it was a single stage paint and layer was fairly thin. So I didnt want to take off too much paint. So no heavy cutter. Gave it a nice coat with 22ple as well. <br /><br />Whatd u do to the 300c? Like stage wise. Did it have a ceramic clear coat?<br />

KAAZ_breakin.gif

Yep, this part I've got down pat...

What I'm wondering about is how crucial is the low speeds and how many km before I switch out the oil for the first time. Considering I'm using a "used" crown wheel, is the low speed stuff mainly to protect that if it was brand new?

Or would higher speeds affect the new LSD Center as well...

 

Yep, this part I've got down pat...

What I'm wondering about is how crucial is the low speeds and how many km before I switch out the oil for the first time. Considering I'm using a "used" crown wheel, is the low speed stuff mainly to protect that if it was brand new?

Or would higher speeds affect the new LSD Center as well...

 

think of it like bedding in brakes... I did this for 30 mins straight away then binned the oil and used motul comp 75w150

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...