Jump to content
SAU Community

Recommended Posts

attachicon.gifImageUploadedBySAU Community1399379492.386155.jpg

Dat micolour & final inspection combo

thats sexeh....

Dat Artz carport finish...

DSCN1212_zpsfacc27cb.jpg

its not waxed yet , but am I close ? :huh:

tbh there is still quite a few scratches in it on close inspection but there is only so much you can do with tired old paint....

I mean i could buff them out but the clearcoat is only going to get thinner...

  • Like 1

thats sexeh....

Dat Artz carport finish...

DSCN1212_zpsfacc27cb.jpg

its not waxed yet , but am I close ? :huh:

tbh there is still quite a few scratches in it on close inspection but there is only so much you can do with tired old paint....

I mean i could buff them out but the clearcoat is only going to get thinner...

Youre putting way too much effort in for a "budget job".

Guy isnt even going to notice the difference between the minor ones only you can see

kinkstah.

your dumppipe looks very sweet.,

i gotta ask, which blind man did the rear of the system?! so we can avoid them at all costs.

Hahahaha.

Yeah.

Nothing at all on my car can be considered to 'look very sweet'

Well yeah, I don't think he is gonna plumb it back for now (re: screamer).

How he is going to fit that into the 5in cat, I do not know. Unless he runs it direct to the body of the cat itself. I believe ARTZ had that done.

But my car cannot be made to 'look very sweet' by the efforts of one man alone.

It will most likely require the efforts of three men, namely scotty, artz, and aaron by the way of his guard roller and general "greg don't do stupid shit" advice.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Bah! I can't see the point in custom number plates at all. I went to the rego office, fished through a box of "premium" plates (the ones that had the "not as tall" option for the front plate) and picked the one that had a 32 in it. That's the limit of the effort and cost I will put into number plates. The only plate that I'd consider paying for would be 2332, but that's not possible here because it already exists from probably 90 years ago, and it would cost a fortune to obtain it, if it were available.
    • After chasing my tail with LS results..... and cheaper than a turbo swap... How confident are you that the dyno is accurate relative to other results? How fast is the car - What MPH does it actually run? Is this similar to what people running this power would expect?
    • Hi mate I am having an identical issue with my 98 R34 GTT. The engie suddenly cuts out under load at about 3-4k, black smoke out exhaust. Almost feels like traction control kicking in. No CEL but still going to check codes later today. Car was sitting in the shed for about 5 months before hand and only idled a few times, took her out with about 1/4 tank, filled up and thats when the issues started happening.  Threw on a spare set of coils/harness and checked plugs which was no help. Recently had fuel pump/filter changed so surely thats not the issue unless condensation in fuel, I just havent had the time to drain it It's running a hi flow turbo, bosch 1000cc injectors, walbro 450L, Z32, Nistune etc... All about 2000km old.
    • I always wonder where the obsession with legal/illegal spacing on number plates in the UK comes from. Because it comes up in comments in every UK-based video I see on youtube. From my point of view all of your plates look a bit odd. Just because there are no markings whatsoever. In Australia we have the state that has to be on it. In Europe you get stamps and state logos. Yours look a bit like a throwaway draft that people then stuck with. And attached with blu tack so that it falls off at the slightest disturbance. Not trying to hate, but it's interesting how things are done in different countries. Do you have to follow a lettering convention when choosing a custom plate?
    • Hybrid sounds like a supercharger... It's half a turbo, with a belt to drive it! Oh wait, they're just called super chargers...
×
×
  • Create New...