Jump to content
SAU Community

Recommended Posts

That said, there is a bit of a saying that if you lend someone $20 and never get it back then it's money well spent

But not 20k

But then what if it was $20 paid in tax used to buy alcohol/ciggarettes/drugs? :P

I've gone through this before for 50 bucks, never getting that back

At least it was only 50 bucks, but still, 50 bucks is 50 bucks. :\

Don't think I'll lend money ever again to friends heh

Also, S22E03 of top gear is funny as f**k. (came out today)

Edited by UNR33L

Is he not paying it back because financially he is not in the position to do so?

Or does he have money now and is just avoiding paying it back.

Your mate needs to figure this out, talk to the guy, say "We agreed that you would pay back minimum $500/fortnight until it was fully repaid, you are not meeting your end of the agreement, why?" and if its a bullshit excuse call him out on it "Saw you shouting beers for everyone after work last night, where's my money man?"

This is why all agreements need to have a non-payment clause, whether it's upped interest rates after a certain timeframe or something, the person needs an incentive to pay it back... $50 isn't worth losing a friend over, $20,000 is more than enough for some people.

wheres-my-money-o.gif

Is he not paying it back because financially he is not in the position to do so?

Or does he have money now and is just avoiding paying it back.

Your mate needs to figure this out, talk to the guy, say "We agreed that you would pay back minimum $500/fortnight until it was fully repaid, you are not meeting your end of the agreement, why?" and if its a bullshit excuse call him out on it "Saw you shouting beers for everyone after work last night, where's my money man?"

This is why all agreements need to have a non-payment clause, whether it's upped interest rates after a certain timeframe or something, the person needs an incentive to pay it back... $50 isn't worth losing a friend over, $20,000 is more than enough for some people.

wheres-my-money-o.gif

Yeah, not like I would loose a friend over 50 just be more careful lending out in future

Yeah, not like I would loose a friend over 50 just be more careful lending out in future

I would lose a friend over 50, as long as you remind them about it and they're scum about paying it back

What kind of asshole does that to someone, when you've helped them out and their response is meh you don't need it back

Doesn't matter the amount

I would lose a friend over 50, as long as you remind them about it and they're scum about paying it back

What kind of asshole does that to someone, when you've helped them out and their response is meh you don't need it back

Doesn't matter the amount

We went on a double date, (I'd seen this girl a couple of times before then) and I basically paid cos needed to pre book

Think it was thought he was being helpful to my cause/date, so didn't feel the need to pay back.. heh

Edited by UNR33L
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...