Jump to content
SAU Community

Recommended Posts

actually for you property people,

what the deal with a loan to buy property? do you look at home loan rates? do they want 10 or 20% deposit?

any thing else should know?

Banks want 20% but s mortgage broker can usually secure s loan for 5-10% ( up to 95 LVR )

actually for you property people,

what the deal with a loan to buy property? do you look at home loan rates? do they want 10 or 20% deposit?

any thing else should know?

Want 20% deposit in order to get best possible rate from a major lender.

Can go less however you will likely have to purchase insurance for the bank - at your cost (LMI)

Major banks want to see a pattern of saving for the deposit

that's all really

I don't really understand the "do you look at rates" part of that... of course you do.

* protip.... the ONLY thing that matters is the comparison rate (ignore the actual rate)

I don't really understand the "do you look at rates" part of that... of course you do.

Was not sure if properly fell under home loan rates or a secured personal loan rate.

as it land not a "home"

was not planning on buying till next year anyhow, so should have a nice easy 25-30 % deposit.

Sweet.

one of my mates dad did exactly that, got sick of the burn outs on the road in front of the farm, built a 30x30 meter skid pan for him to use as a 21st present, when son moved out, turned into a feed lot for the cows.

but the land above was over 800 meter long...drag strip or GTFO

actually for you property people,

what the deal with a loan to buy property? do you look at home loan rates? do they want 10 or 20% deposit?

any thing else should know?

20% avoids lenders mortgage insurance but some lenders will do 5% at the moment

Not sure if it's different for farms like I know units below are certain size require more deposit

Ham might know more

Bank's shade the value of a security to create "bank value"

Industry standard shading is 20% hence the usual 80% lend

Rural property is often shaded at 30% hence requiring a 70% maximum lend without the bank looking for insurance.

Banks do not like lending above 100% of "Bank Value" hence places like UBank not looking at anything above an 80% LVR

On windows 7 at work now... just hooked myself up with 3 screens...

it's like the god damn Nebuchadnezzar up in here

Only just got windows 7?

I run 3 screens at work as well gives me a headache sometimes lol

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...