Jump to content
SAU Community

Recommended Posts

  • Replies 231
  • Created
  • Last Reply

Top Posters In This Topic

to run a 10 in a full weight gtst, you will need good tyres, try aim for something better then ET street radials because they wont cut it, about 375rwkw, a good clutch and also a decent launch control and ecu with a tuner who can sit with you at the track and play with boost control trim on gears, boost control trim on wheel spin, and ignition timing retard on wheelspin, and also the launch control must not spool too much boost off the mark.

you need a 1.6 or lower 60 foot before you will grab it also.

Its not easy to do on a full weight street car, but i never gave up until i cracked it, i ran 10.80 @ 135mph before i gave up.

if you want to run the 10 you need to put in some hard work!

Except it hasn't done a 10 yet :P

I differ in opinion to most people who want to run 10s

A single 10.9999999 is different to a car setup to run half a dozen in a row. That is where car setup is important

I also don't like to see people wanting a 10 sec streeter but not want to drag "race" ie something other than a off street Wednesday night

I understand not everyone wants to cage their car....

If you don't, set it up to run consistent low 11's and hit the track as much as you like

That's gotta be one* of the dumber things you've posted.

*aside from the 2JZ/Supra talk on a RB/Skyline based forum

If someone wants a street car, on DOT radials that can run a 10.

And drive it around daily, for a reasonable budget - who cares about a "real" comp.

That's gotta be one* of the dumber things you've posted.

*aside from the 2JZ/Supra talk on a RB/Skyline based forum

If someone wants a street car, on DOT radials that can run a 10.

And drive it around daily, for a reasonable budget - who cares about a "real" comp.

LOL I agree with that one, that Zebra seriously needs to go back to the zoo! ..Saying after reading some of his posts..>_<

ahhh you guys are f**king retarded >_<

you guys want to spend 11ty $$$$ on getting a car to run a 10...ONCE..because you will be booted...then what....spend more money on changing it to a circuit car

Silly me for thinking people who want a "10 second car" actually want to run 10's more than once.

Its like buying a V8 Commodore.... Its no special supercar out of the factory, not unless you buy something really expensive..

But hey if you want a V8 taxi then thats good for you. On the same token if somebody wants a 10 second skyline for the sake of saying I have a 10 second skyline then good for them too LOL

*aside from the 2JZ/Supra talk on a RB/Skyline based forum

Oh Noez!!!!

God Forbid any variety on the internet....Don't tell me you snatched the rights to "Nissan Skyline" too so you can claim it as your own and make money of others hard work

i thought WSID was introducing the new rule cause heaps of owners of new Fords & holdens where complaining about putting cages in there brand new $80K cars..

most these cars can run 10's for under $5000 of mods..

to run a 10 in a full weight gtst, you will need good tyres, try aim for something better then ET street radials because they wont cut it, about 375rwkw, a good clutch and also a decent launch control and ecu with a tuner who can sit with you at the track and play with boost control trim on gears, boost control trim on wheel spin, and ignition timing retard on wheelspin, and also the launch control must not spool too much boost off the mark.

you need a 1.6 or lower 60 foot before you will grab it also.

Its not easy to do on a full weight street car, but i never gave up until i cracked it, i ran 10.80 @ 135mph before i gave up.

if you want to run the 10 you need to put in some hard work!

Ive gone the easy way and have a C4 and 3800 stall. But dont have the 10 yet but shouldnt be far away :thumbsup:

Most people also don't realise how quick a 10 second car is. Fastest car i've ever been in was my dads R33 with 350rwkw, did a low-mid 11 @ 125mph which was freaking quick. Not saying this about OP, but a lot of guys go from a stock liner and think "oh i want a 10 second car hepa derpa" without knowing how quick it really is.

i thought WSID was introducing the new rule cause heaps of owners of new Fords & holdens where complaining about putting cages in there brand new $80K cars..

most these cars can run 10's for under $5000 of mods..

Nope, they did a backflip on the decision unfortunately

never happen on street tyres

drag radials as a minimum and you would be looking at 550+bhp at the crank to get you a high 10 at around 130mph after lots of practice

Auto or manual?

Lots of practice.... PFFT I did one pass :nyaanyaa: But I guess it wasn't a 10 :pirate:

In a manual, you would need atleast 400rwkw and MT Streets and know how to drive. Really drive.

I had 360rwkw (dyno dynamics) or 410rwkw (dynapac with correction) and yes knowing how to peddle well and smash gears helps

to run a 10 in a full weight gtst, you will need good tyres, try aim for something better then ET street radials because they wont cut it, about 375rwkw, a good clutch and also a decent launch control and ecu with a tuner who can sit with you at the track and play with boost control trim on gears, boost control trim on wheel spin, and ignition timing retard on wheelspin, and also the launch control must not spool too much boost off the mark.

you need a 1.6 or lower 60 foot before you will grab it also.

Its not easy to do on a full weight street car, but i never gave up until i cracked it, i ran 10.80 @ 135mph before i gave up.

if you want to run the 10 you need to put in some hard work!

I don't think you need a lot of the things you have listed >_<

Most people also don't realise how quick a 10 second car is. Fastest car i've ever been in was my dads R33 with 350rwkw, did a low-mid 11 @ 125mph which was freaking quick. Not saying this about OP, but a lot of guys go from a stock liner and think "oh i want a 10 second car hepa derpa" without knowing how quick it really is.

Also on the street a 10sec car isn't really a 10sec car... Unless it's a GTR :)

Edited by SimonR32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...