Jump to content
SAU Community

Recommended Posts

  • Replies 231
  • Created
  • Last Reply

Top Posters In This Topic

to run a 10 in a full weight gtst, you will need good tyres, try aim for something better then ET street radials because they wont cut it, about 375rwkw, a good clutch and also a decent launch control and ecu with a tuner who can sit with you at the track and play with boost control trim on gears, boost control trim on wheel spin, and ignition timing retard on wheelspin, and also the launch control must not spool too much boost off the mark.

you need a 1.6 or lower 60 foot before you will grab it also.

Its not easy to do on a full weight street car, but i never gave up until i cracked it, i ran 10.80 @ 135mph before i gave up.

if you want to run the 10 you need to put in some hard work!

Except it hasn't done a 10 yet :P

I differ in opinion to most people who want to run 10s

A single 10.9999999 is different to a car setup to run half a dozen in a row. That is where car setup is important

I also don't like to see people wanting a 10 sec streeter but not want to drag "race" ie something other than a off street Wednesday night

I understand not everyone wants to cage their car....

If you don't, set it up to run consistent low 11's and hit the track as much as you like

That's gotta be one* of the dumber things you've posted.

*aside from the 2JZ/Supra talk on a RB/Skyline based forum

If someone wants a street car, on DOT radials that can run a 10.

And drive it around daily, for a reasonable budget - who cares about a "real" comp.

That's gotta be one* of the dumber things you've posted.

*aside from the 2JZ/Supra talk on a RB/Skyline based forum

If someone wants a street car, on DOT radials that can run a 10.

And drive it around daily, for a reasonable budget - who cares about a "real" comp.

LOL I agree with that one, that Zebra seriously needs to go back to the zoo! ..Saying after reading some of his posts..>_<

ahhh you guys are f**king retarded >_<

you guys want to spend 11ty $$$$ on getting a car to run a 10...ONCE..because you will be booted...then what....spend more money on changing it to a circuit car

Silly me for thinking people who want a "10 second car" actually want to run 10's more than once.

Its like buying a V8 Commodore.... Its no special supercar out of the factory, not unless you buy something really expensive..

But hey if you want a V8 taxi then thats good for you. On the same token if somebody wants a 10 second skyline for the sake of saying I have a 10 second skyline then good for them too LOL

*aside from the 2JZ/Supra talk on a RB/Skyline based forum

Oh Noez!!!!

God Forbid any variety on the internet....Don't tell me you snatched the rights to "Nissan Skyline" too so you can claim it as your own and make money of others hard work

i thought WSID was introducing the new rule cause heaps of owners of new Fords & holdens where complaining about putting cages in there brand new $80K cars..

most these cars can run 10's for under $5000 of mods..

to run a 10 in a full weight gtst, you will need good tyres, try aim for something better then ET street radials because they wont cut it, about 375rwkw, a good clutch and also a decent launch control and ecu with a tuner who can sit with you at the track and play with boost control trim on gears, boost control trim on wheel spin, and ignition timing retard on wheelspin, and also the launch control must not spool too much boost off the mark.

you need a 1.6 or lower 60 foot before you will grab it also.

Its not easy to do on a full weight street car, but i never gave up until i cracked it, i ran 10.80 @ 135mph before i gave up.

if you want to run the 10 you need to put in some hard work!

Ive gone the easy way and have a C4 and 3800 stall. But dont have the 10 yet but shouldnt be far away :thumbsup:

Most people also don't realise how quick a 10 second car is. Fastest car i've ever been in was my dads R33 with 350rwkw, did a low-mid 11 @ 125mph which was freaking quick. Not saying this about OP, but a lot of guys go from a stock liner and think "oh i want a 10 second car hepa derpa" without knowing how quick it really is.

i thought WSID was introducing the new rule cause heaps of owners of new Fords & holdens where complaining about putting cages in there brand new $80K cars..

most these cars can run 10's for under $5000 of mods..

Nope, they did a backflip on the decision unfortunately

never happen on street tyres

drag radials as a minimum and you would be looking at 550+bhp at the crank to get you a high 10 at around 130mph after lots of practice

Auto or manual?

Lots of practice.... PFFT I did one pass :nyaanyaa: But I guess it wasn't a 10 :pirate:

In a manual, you would need atleast 400rwkw and MT Streets and know how to drive. Really drive.

I had 360rwkw (dyno dynamics) or 410rwkw (dynapac with correction) and yes knowing how to peddle well and smash gears helps

to run a 10 in a full weight gtst, you will need good tyres, try aim for something better then ET street radials because they wont cut it, about 375rwkw, a good clutch and also a decent launch control and ecu with a tuner who can sit with you at the track and play with boost control trim on gears, boost control trim on wheel spin, and ignition timing retard on wheelspin, and also the launch control must not spool too much boost off the mark.

you need a 1.6 or lower 60 foot before you will grab it also.

Its not easy to do on a full weight street car, but i never gave up until i cracked it, i ran 10.80 @ 135mph before i gave up.

if you want to run the 10 you need to put in some hard work!

I don't think you need a lot of the things you have listed >_<

Most people also don't realise how quick a 10 second car is. Fastest car i've ever been in was my dads R33 with 350rwkw, did a low-mid 11 @ 125mph which was freaking quick. Not saying this about OP, but a lot of guys go from a stock liner and think "oh i want a 10 second car hepa derpa" without knowing how quick it really is.

Also on the street a 10sec car isn't really a 10sec car... Unless it's a GTR :)

Edited by SimonR32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...