Jump to content
SAU Community

Recommended Posts

Test fitted some wheels.

F - 9 +30, 255

R - 10 +38, 295

With about 2.5 deg camber on the rear it was slightly pokey, and flush with 2 deg camber on the front.

Decided to go with,

F - 9 +35

R - 9.5 +38

RPF1s on their way from japan, hope this helps anyone looking to go big.

10588654_814795625218233_842044625_n1_zp

10585598_814803338550795_616279295_n_zps

  • 4 weeks later...
  • 3 weeks later...

I put on something similar Koya Cr Tek 18 x 8.5 +32 offset all round with Federal 595 235x 40x 18

Car is GTT r34.

Had the original wheela on it before handles excellent. No guard rolling.

  • 2 months later...

I want 18x9.5 inch all round, rears im fine with +38 but for the fronts its hard to find out exactly what offset i would need.

I would prefer no gaurd roll back can do if scraping.

Would +35 front be ok?

9.5 + 35 probably wont clear the inner suspension on the front.

You would probably need to go for a much lower offset if you want 9.5 on the front.

I went 18x9.5 +22, Volk Racing TE37SL's with 245/35/18 tyres.

Guards are rolled just to be safe and car is lowered w Coilovers.

Clears the plastic lining in the front with no rubbing at all.

Slightest poke on the front but hardly noticeable.

IMG_87292222_zpsc5b30122.jpg

10834093_10153371011077571_1859539448_n_

10743558_10153312105092571_69778459_n_zp

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
×
×
  • Create New...