Jump to content
SAU Community

Walbro 400Lph Problem

Hadouken

By Hadouken,
in Engines & Forced Induction

 Share

Recommended Posts

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

XKLABA
XKLABA

Don't flatter your self about the non return valve idea, we have been using them for more then 20years in the race cars My brothers car, I don't have a pic of mine in my phone It runs a VQ35HR wi

scotty nm35
scotty nm35

Because it is perfect, for me and my setup. I guess you just don't appreciate the hard work I put into it, designing a failsafe system on my own, using a single reg and return when everyone on here wa

Ben C34
Ben C34

To seperate the banks and use one reg wouldn't it go Pump > rail> non return > tee piece to common reg on both sides? Pretty easy.

Posted Images

SiR_RB Grand Master

SiR_RB

Posted
Posted

I may have made a mistake, my pump kit came with a black rubber sock/sleeve that goes over the pump for when it's mounted externally to stop vibrations etc while clamped down....

I put that around the body of the pump submerged in the tank in ethanol....I'm going to check it this avo I have a feeling it's starting to perish and block the intake sock on the pump lol

  • 1 year later...
The Mafia Grand Master

The Mafia

Posted
Posted

Sorry about the thread revival guys, but I am at a moot point regarding fuel pumps and it is driving me mad.

What I plan on doing is running a pump on its own (With the intentions of it becoming a lift pump once I need more fuel).

I have a brand new Nismo 275lph @ 80psi pump sitting in a box wrapped in plastic. I've been told not to use it for E85, and I want to use E85. People have told me to get a Walbro 400lph pump which is E85 compatible. So I did some homework:

The walbro 400lph isn't exactly that. (I have attached flow diagrams)

It flows 315lph at 70psi (45psi base, 25psi of boost)

Nismo flows 275lph @ 80 psi which I estimate to be over 300lph at 70psi.

Anyway - should I just drop the Nismo in and run E85 through it and be done with it?

I love Nismo pumps. So quiet, small, and, its Nismo!

post-7271-0-88763900-1407373396_thumb.jpg

scotty nm35 Grand Master

scotty nm35

Posted
Posted

The ethanol version of the Walbro is absolutely silent, quieter than the Nismo/Tomei pumps. It uses a turbine vane, not an oil pump style gear type of old.

If you want ethanol compatibility there is only one choice, that said, you may get many years out of the Nismo. Personally I would sell the Nismo off and buy the 460 Walbro, and pocket the change.

The Mafia Grand Master

The Mafia

Posted
Posted

Mr Mafia is that the R33 GTR or GTS25T Nismo pump ?

Personally I think an EFI pump that draws 18-20 amps on its own is hardly current tech electrics . I think the GTR Nismo is advertised as drawing 8 or 9 .

A .

R34 GTR Nismo pump Disco stu :)

If it's a 8-9 amp pump, what does this mean for me?

And works with the factory fpcm, but I don't think Mafia needs that. :P

haha actually... yes I do. I am running a Nistune (R32 GTR ECU in my R34 GTR). Works really well.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

R34 GTR Nismo pump Disco stu :)

If it's a 8-9 amp pump, what does this mean for me?

haha actually... yes I do. I am running a Nistune (R32 GTR ECU in my R34 GTR). Works really well.

Have you, or are you planning to direct wire the pump through a relay? The stock wiring won't support the Walbro.

discopotato03 Grand Master

discopotato03

Posted
Posted

Twice the current draw from a battery that's sometimes not real close to the alternator .

I haven't looked that closely into the fuel pump control modules , basically they are like a ballast resistor with a fancy relay to bypass it when the computer says so . With GTRs the FPCM has two stages or resistors and the usual bypass . Nissans like the Q45 V8s in the US use the same type of thing and at one of their sites they have pics of them opened up and in various stages of melt down - literally .

Their purpose was to minimise the amount of fuel doing circuits at low revs and loads and to shut the pump up to a degree .

The upshot is that the standard wiring won't appreciate more than double the fuel pumps normal current draw which is why the bolt in Nismo pump works with the standard system .

One feller many years ago reckoned an easy way is to leave the std or similar pump in tank and run an external pump to do the hard stuff . A standardish pump should easily cope feeding into the external because its not creating the rails pressure head on its own . . And its not like either pump can run away speed wise because all the fuel is going to the same place . External pumps make the wiring easy because there's no fuel tank to feed/seal wires into . Bonus is they're easy to change if you mount them in an accessible place .

In a way running pumps in circuit is like running several in tank because logically the fuel all goes to the same place . The difference is that running them in series rather than parallel means they share the work load and if primary isn't a gorilla pump it doesn't matter . If the external tries to pump more than the in tank its flow increases because the effective pressure ahead is less .

A .

scotty nm35 Grand Master

scotty nm35

Posted
Posted

which is why the bolt in Nismo pump works with the standard system .

No, the Nismo works on the stock system because it is designed to run on low voltage, and not draw too much current for the stock wiring when doing so. Try running a Walbro 255 on stock cruise voltages and you will find it doesn't last very long.

Personally I run twin 255's for that very reason, more flow for less current, but they are not ethanol rated. These days I would be dropping an e85 460 in, as I am doing to my evo this week.

Running the stock pump with an inline after it is a good idea, but you would need to match the sizes of the pumps. No way a little 20 year old oem stock pump will flow enough to keep up with a decent inline, and that would cause all sorts of problems.

  • 4 weeks later...
boostn0199 Grand Master

boostn0199

Posted
Posted

lol so I am still confused. Should I just use the Nismo for my intank pump for E85, and then upgrade to a surge tank when I need more and then use the nismo as a lift pump?

Thats what I did had the nismo initially and then it became my lift pump when I went surge so far 4 years on e85 and no problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
    • TurboTapin
      Most women will agree that parking is the most taxing part of driving

      By TurboTapin · Posted

      What a time to be alive!!
×
×
  • Create New...