Jump to content
SAU Community

Recommended Posts

What sentences does it contain, in case we missed something?

34 minutes ago, BakemonoRicer said:

The EFR speed sensor is the limit not the fuel system (its an obvious Stage 4 1000hp+ setup). 

This build doesnt contain the sentence.... "let's play it safe".......

 

13 hours ago, BakemonoRicer said:

The EFR speed sensor is the limit not the fuel system (its an obvious Stage 4 1000hp+ setup). 

This build doesnt contain the sentence.... "let's play it safe".......

Yeah you missed the point there champ, I was complimenting the fuel system as it's far more capable than the very obvious limitation of the bottom end surviving all the EFR can throw at it. Given the stage 4 crap though I assume I have just fed the troll and been successfull baited lol good job. 

12 hours ago, Ben C34 said:

What sentences does it contain, in case we missed something?

 

My guess is either "that's really as far as we shoud push" or "f**k, we tried to warn you".

Just now, ActionDan said:

Sounds like I wasted a f**k load of money for my power goal vs spec list then... 

 

 

but you want max torque, best lap times.. you didn't want to build a Maccas Carpark Stance Box and Internets Dyno bragging car though

  • Haha 2

LOL that quote will stay with me for a while "Maccas Carpark Stance Box".

I'm hoping to outdo my mates and get like, maybe a WHOLE season of like 7-8 events before it blows apart.. 

f**king SR20s, why didn't I K-swap lol

 

3 hours ago, ActionDan said:

LOL that quote will stay with me for a while "Maccas Carpark Stance Box".

I'm hoping to outdo my mates and get like, maybe a WHOLE season of like 7-8 events before it blows apart.. 

f**king SR20s, why didn't I K-swap lol

 

I once tuned a S15 slammed on the ground (stock turbo, flex conversion, Nistune, R35 AFM)

image.png.f5d6f49663548a9f2930b87e760b39eb.png

Dropped off the Emtron to Insight today

Progress is kicking along well looking like it’ll be set for the dyno next week or week after

this build honestly Is a hamburger with the lot no corners cut , just need a sponsorship from samsonas ! Lol 

Stop messing about Benji, I want to see the photos of the Carillo rods and 11.5:1 JE Pistons with custom spec gudgeon pins you dropped off with the Emtron. Will give you one bonus post-Covid elbow-bump if there's any billet engine brace in sight.

  • Haha 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
×
×
  • Create New...