Jump to content
SAU Community

Recommended Posts

For every ones info. I replaced the V Spec II sticker on my car, with a genuine Nissan sticker. It was super expensive, but aside from that, the sticker is shaped to match the corner of the back boot like a template. This means that you can use the corners and edges of the boots to get the sticker in the exact factory position. Pretty sweet. I was surprised.

Just checked my spare sticker (my original is just showing a tiny amount of peel on one corner....) - you are right - how clever of them......

Cheers

The Baron

PS That Edward Lee Video should be pinned somewhere as a "must see" for anyone who ever considers buying a car from that guy, with annotations about all the misleading statements.......

Good luck this weekend Bob! :D At the very least I'm sure you will have fun!

Yep had fun but my times were ..........OK????????

My best 1/4 mile was 13.399 (slip attached) but my best terminal speed was 178.94 kph a couple of runs later (111mph).

With that speed I should have been well into the 12's but my 0-30' times are horrible.

I just can get it off the line. I tried it in 2WD mode by pulling the fuse but that was worse!!!!!!

I just sat there and smoked the tyres. :closedeyes::closedeyes::closedeyes::closedeyes::closedeyes:

Anyway, I flogged a few of my mates in stock HSV's and GT Falcons (mid to low 14"s)!

Cheers,

Bob.

post-78207-0-53167100-1403937609_thumb.jpg

Its all in tyre pressure Bob. Need to be 15psi from memory, can't remember exactly but it's a super low pressure.

Once that is set, 2nd gear burn out in rwd mode then flick to awd, on the limiter and release the clutch...when it hooks up you will be shocked what g's these cars can pull on take off.

Mine did a flat 13 when it was stock as a rock...won't get much better than that although I've heard they run a PB 12.8

Thanks Marko,

Modern Motor (April 1990 issue) ran a 13.1 stock........ That's the best I've seen in any publication. Most run around 13.7.

My tyres were set at 27psi for the fronts and 22 psi for the rears...... Guess I stuffed up on that one.

I normally run them at 34 and 30 on the road.

Was pleased with the terminal speed though.

Bob.

At 111mph it's not stock and probably making closer to 270kw at the wheels and should be doing flat 12s or even into the 11s

100% correct........ Unigroup dyno'd it at 271.6 rwkw.

Bob.

what is not stock on the car Bob?

Bar the exhaust, (3.5" front Pipe, 3" Hi Flow Cat, 3.25 Rear pipe, 3 and Hiflow rear muffler) everything you CAN'T see.......

  • Nistune
  • Sard 720cc injectors
  • Lager Walbro fuel pump
  • HKS Boost Controller
  • Splitfire coils
  • Excedy HD Clutch

Bob.

Bar the exhaust, (3.5" front Pipe, 3" Hi Flow Cat, 3.25 Rear pipe, 3 and Hiflow rear muffler) everything you CAN'T see.......

  • Nistune
  • Sard 720cc injectors
  • Lager Walbro fuel pump
  • HKS Boost Controller
  • Splitfire coils
  • Excedy HD Clutch
Bob.
nice. The Walbro pump is not to noisy?

nice. The Walbro pump is not to noisy?

No....... The exhaust must drone it out!

A mate of mine had a Brock Commodore VK Group A that was tricked up with a Walbro pump and that was horrendously noisy so I know what you mean.

Bob.

Yep had fun but my times were ..........OK????????

My best 1/4 mile was 13.399 (slip attached) but my best terminal speed was 178.94 kph a couple of runs later (111mph).

With that speed I should have been well into the 12's but my 0-30' times are horrible.

I just can get it off the line. I tried it in 2WD mode by pulling the fuse but that was worse!!!!!!

I just sat there and smoked the tyres. :closedeyes::closedeyes::closedeyes::closedeyes::closedeyes:

Anyway, I flogged a few of my mates in stock HSV's and GT Falcons (mid to low 14"s)!

Cheers,

Bob.

That's still very respectable, and at least you had fun... that's the main part!

How were you launching the car Bob? These things need a little tough love from the start line, you might feel bad in doing it but it's what she's made for :) There's absolutely more to be had from your car, your 60 foot time of 2.1s could come down to 1.6 to 1.8 seconds with a bit of practice - I'm not a drag racing expert by any stretch of the imagination but that little bit shaved off the front end often seems to translate to a larger amount shaved off at the other end.

Well done in any event, at least you came out the winner against the HSVs and FPVs! :)

  • 1 month later...

So just an update on my gtr,

Installed new timing belt, HKS cam gears, water pump etc,

Bought a power fc and some hks 550cc injectors.

I had a second hand apexi avcr so I just used the boost solenoid and wiring and converted it to my power fc.

Got the car back from the tuner today and made 265kw's on 1.1bar boost!

Pretty happy and the car feels a hell of alot more alive than before!

post-90998-0-26142400-1406888757_thumb.jpg

  • 3 weeks later...

Hey guys,

I've been off sau for a year or two. Sure we used to have another rare register with a good record of vpsecs and n1s? I'm probably just lost tho, lol.

Anyway adding for the community, in Brisbane with a 1994 Vspec II N1. Unfortunately not very standard! :-)

Cheers

Michael

Fortunately, Australia has acquired 2x BNR32 V-Spec II N1 in recent times.

Congratulations to you Michael as well.

We'd like to grab them before Canada's timeline permits...

Last six digits on mine are -311603

Terry-36_zpsc2e1370c.jpg

It's still awaiting compliance.

  • Like 2

Fortunately, Australia has acquired 2x BNR32 V-Spec II N1 in recent times.

Congratulations to you Michael as well.

We'd like to grab them before Canada's timeline permits...

Last six digits on mine are -311603

Terry-36_zpsc2e1370c.jpg

It's still awaiting compliance.

is that a genuine N1 Terry?

Car looks very nice.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
×
×
  • Create New...