Jump to content
SAU Community

Recommended Posts

Here's one I tried some AMMO on Matt...personal project I've been working on, I spent the best part of three days with the polisher on most of the major panels...but bumpers ,mirrors are too faded and will require repainting though when I get some time so i wont to bother show pics of them...Unfortunately with the lighting conditions of my carport and the 23 yr old paint, its near impossible to get every scratch out...but its close ...

Has a few layers of skin and 1 of creme atm, but i think my favourite so far has to be the hydrate.....its very enjoyable to use for everyday detailing duties :)

DSCN0542_zps69f38061.jpg

DSCN0783_zpse04af55c.jpg

  • 2 weeks later...

Picked up some IronX a couple weeks back, had heard some pretty good things about it and wasnt disappointed!

Start with some pretty filthy wheels

post-61032-0-78627000-1391767290_thumb.jpg

Spray and leave for a few minutes

post-61032-0-77473800-1391767312_thumb.jpg

Then clean off

post-61032-0-29341400-1391767345_thumb.jpg

And finished with some Poorboys wheel sealant and also Poorboys tyre gel

post-61032-0-44549000-1391767410_thumb.jpg

  • Like 1
  • 1 month later...

Pretty much my first real attempt at detailing and polishing, did it on my new home respray job on my track car.

Used a super cheap DA polisher then scholls s3 gold for cutting and s30+ for polish as recomended from Antonio from waxit and I'm very happy how well the product works no mess at all! Car was rubbed down with 2000grit wet after spray before cut and polishing it.

post-50426-0-82228100-1395743003_thumb.jpgpost-50426-0-57843300-1395743066_thumb.jpgpost-50426-0-40945500-1395743110_thumb.jpgpost-50426-0-56915300-1395743167_thumb.jpgpost-50426-0-24795900-1395743210_thumb.jpg

  • 2 weeks later...

my new home respray job on my track car.

Looks like it came up pretty good :thumbsup:

I've got a couple of panels here i've meen meaning to have a crack at but i've got no idea, what process/steps did you use? (sand > clean > primer > paint > clear > sand > polish) etc.

Quick wash and clay, followed by testing out Mothers Mag & Aluminum Polish on the lip. Came up heaps better but definitely more to go. Spent probably 20 minutes just on the lip of this one, need a hell of a lot of elbow grease.

post-63773-0-89092700-1396515812_thumb.jpg

Looks like it came up pretty good :thumbsup:

I've got a couple of panels here i've meen meaning to have a crack at but i've got no idea, what process/steps did you use? (sand > clean > primer > paint > clear > sand > polish) etc.

pg[/url]

Process was basically get thd body dtraight since it was completly damaged both sides so alot of oxy and body filler lol but then it was final sand , primer, 800 grit sand, fill any holes with putty, sand putty with 400, then primer over putty areas, sand 800 again, paint, then sand 2000 , cut, polish.

I didnt use a clear since its a solid colour and also its going to be constantly repaired and touched up so makes it easier with no clear. In saying that i consoder my process a rough job if you want to go step further after paint sand down with 1200 then 1500 then 2000 folowed by cut polish will give a perfect finish but takes considerably longer since that last sanding process takes the longest.

Edited by boostn0199

C'mon dude where's the photo of your reflection in the paintwork....anything can look shiny from a distance. :rofl:

loll kind of ran out of time and and no good lighting at the time ended up finishing the job at like 4am took those couple of pics then onto the trailer and drift event next day, now its dirty again, will get some closeups after i wash it next time.

Hi Nicr4wks,

I was running with the distribution of AMMO in Australia.

Unfortunattly when it was first released we were not seeing a high enough volume and shipping was too expensive for our volumes.

I would suggest that the cheapest option would be for you to purchase directly from the ammo website.

You will find that the cost of the suff online is the same price if not cheaper

Cheers,

Matt

www.upcd.com.au

Hi, I did not take any before shots , this car was in a garage for 5 years and I think it must have had holes in the roof, the water etchings were really deep and took forever to get the crap out.

Going to wax it when it get it back from the workshop :yes:

post-52098-0-86726300-1397026240_thumb.jpg

post-52098-0-68516600-1397026200_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...