Jump to content
SAU Community

Recommended Posts

It was way too low! Scraping the leading edge the whole way around the track.

We modded and lifted it 15mm or so. Just scraps a little under big load.

I went out without the splitter in the first session. Cold, fresh tyres. Did a high 1.35 on the last lap (6). I'd say with that setup it would be a mid 1.34 I'd say. The splitter is amazing under brakes and on loaded turn in. There is much more time in it.

The fastest lap was terrible. With the setup as is, 1.32 no worries.

Still getting used to this no ABS thing. Plus added aero mods.

Video to come. But the fastest lap was well into the session, generally fastest lap is first or second hot lap.

Did i miss it in the thread.....why no ABS? Is it because your still running the non-ABS diff.....or you just decided to go no ABS from now on?

Man its crazy to see all the cars/changes that have happened over the past 3 or so years summed up in a few pages!

Nice work with the win at WInton!

Cheers,

Dave

nice feature!

good to see the test day went well, do did you notice much difference with the splitter off with the front bar all sealed up? or does it need work in conjunction with the splitter?

Did i miss it in the thread.....why no ABS? Is it because your still running the non-ABS diff.....or you just decided to go no ABS from now on?

Man its crazy to see all the cars/changes that have happened over the past 3 or so years summed up in a few pages!

Nice work with the win at WInton!

Cheers,

Dave

Diff is still in pieces, still using brothers non ABS housing diff.

nice feature!

good to see the test day went well, do did you notice much difference with the splitter off with the front bar all sealed up? or does it need work in conjunction with the splitter?

Can't say I felt a difference.

MAD for taking away the ABS ! :)

I read in a jap magazine that the AD08R are the same compound as the AO50...differences are tread compound and the changes required to allow for smaller tread blocks. So should be pretty close to AO50 if setup right

mmm, not sure about that. It's a similar compound, it's not the same. They tyre doesn't go into a marshmallow state once warm like the 50's do.

Mate, 10/10 for effort and commitment!

Couldn't believe it when I read 'then this happened'... for the 2nd time and then you tagged the wall again! But hats off to ya and clearly paying off.

Car is looking pretty good and getting very serious. Get as much power out of that donk as you can as it makes a big difference at EC as you know!

Good luck at WTAC :)

It was way too low! Scraping the leading edge the whole way around the track.

We modded and lifted it 15mm or so. Just scraps a little under big load.

I went out without the splitter in the first session. Cold, fresh tyres. Did a high 1.35 on the last lap (6). I'd say with that setup it would be a mid 1.34 I'd say. The splitter is amazing under brakes and on loaded turn in. There is much more time in it.

The fastest lap was terrible. With the setup as is, 1.32 no worries.

Still getting used to this no ABS thing. Plus added aero mods.

Video to come. But the fastest lap was well into the session, generally fastest lap is first or second hot lap.

any sign of said vid?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...