Jump to content
SAU Community

Recommended Posts

exactly what im aiming for... starlet is 1.3 engine also yes?

fabricator reckons itll pull crazy power..... im not so sure. engine is 300k old...

1331cc 321,000km engine.

Also it's my wife's car :)

so this weekend, we finished the cooler piping, and made a custom intake using a rip off hks filter from china!

car runs and runs well, although we have the bov completely disconected from the cooler piping as too stop the boost getting to the engine.

specs.

1275 300km engine

ga15 throttle body and afm

custom manifold

custom cooler piping

ford xr6 turbo intercooler

1 x t28 garrett gtr turbo.

future mods (to support e85)

gtst fuel pump.

cga3 top feed fuel rail, modded with vq25 injectors to fit cg13 intake mani.

exedy hd clutch

jun 3.4kg flywheel. (or 4kg cant rememebr)

hopefully get this done over the next two weekends.... tune is 6th of june. (if the nistune is ready in time)

the little micra that could, rajabdamn.

cant believe you got the fuel rail to work with those bits and pieces, usually they are a PITA to get different things to fit.

Where did you source the clutch and flywheel? did they double the budget of this build?

the little micra that could, rajabdamn.

cant believe you got the fuel rail to work with those bits and pieces, usually they are a PITA to get different things to fit.

Where did you source the clutch and flywheel? did they double the budget of this build?

havent got the fuel rail to fit yet.

yes it will be fidlly, but its been done before, the only issue is clearance.....

i got the clutch and fly in a package with the hks/ohlins/tein suspension setup. and it cost just under a years rego.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...