Jump to content
SAU Community

Recommended Posts

G1W on Ebay $48 , i have been running two , one in my work car and misses car for 2 years now - no probs

high def , works perfectly well in low level light/night and bad weather .

There is a G1W Review by Techmoan on YT .

I have 2, 1 for 32 and 1 for work. Basically there "in case". (actually, didn't have it on once and had a near miss, so always have it on now). I run them off the cig lighter socket so I know they will be working.

Although its supposedly HD, doesn't look the clearest when played back on my laptop, but laptop doesn't have HD monitor.

I had one in my delivery ute for about 2 years now.

About 3 months ago a B Double changed (swerved) lanes fast on the Westgate bridge, i was in the left lane and he didnt see me at night, whole drivers side was torn apart, passanger side was crushed into the guard rails, suspension was busted, ute was totaled and he did a runner.

Dash cam caught the whole thing, handed a copy on USB to the police, truck driver lost his licence and from the footage they made a pretty long charge sheet including hit and run, tail gating, dangerous driving, plate on the rear obscured etc.

Police told me i may not need to attend court as the footage is pretty much showing the whole thing from the drivers seat.

If they can prove in court he knew it happened (you can see his trailers swerving as they bounced off the side of my car and he first made contact with his steering wheels so he felt it through the steering wheel), police said it would be a mandatory 6 months jail for the driver as its a hit and run.

Lets see how good his lawyer is.

Cannot tell you all how good it is to have a onboard camera.

Without it he would have got away and i would have paid the excess and taken the blame for it.

And the punch line for the truck driver is when police called him into the interview room once they caught up with him by getting the plates from up the side as i was next to him, he said he was home, his wife could vouch for it and the truck was locked up in the yard on the night of the accident.

Police asked him if that was his statement, he said yes, they got him to sign the statement, then they spun a lap top over to him and hit play, the guy went red when he saw the footage and they asked him if he wanted to make another statement.......they got him for making a false statement too.....

Dickhead.

Get a dash cam, you think you will never need it (my family use to laugh at me for getting one) and it paid itself.

Edited by GTRPSI
  • Like 7

The part that had me worried was when police asked me if i got the rego number of the truck, i didnt know if i did.

I looked at the police officer and said, when it happened, i went into survival mode, i actauly ducked my head to the left while keeping the ute as straight as possible thinking one of the trailers might collect the B pillar behnd my head and take the roof off (and my head) with it.

The part of the bridge where it happened was near its highest, a good 100m up over the city, im in the left being smashed into a steel guard rail by a B double, if that guard rail failed it would have been game over very quickly.

Then the breath test, and the doubt i was telling the truth (police need to be like this), they called the people who montor the cameras on the westgate bridge while is was there only to be told they dont record and are monitored in real time and that the camera operator missed it.

I mentioned to the police i had a onboard camera but had not looked at it for close to 2 years, i knew it worked because everytime i started the car i could hear it chime as it turned on.

Got home, put the memory card into the PC and the whole thing could be seen as clear as day, my unit was on the back window looking over my left shoulder so you could see my speedo in real time, it also has GPS Tracking so you can see where you are on google maps, it also shows the speed on screen from the GPS tracking to backup my speedo reading and the date and time.

The other good thing is i wont need to waste my time going to court to back up the police, its a birds eye view of the whole event, before, during and after, police were surprised to see i survived and said i was very lucky, it could have easily turned into a fatality.

For court, nasty images help the judge come down harder as the seriousness of the crime is shown.

The truck driver certainly would have got away without the camera.

What cam do you have? If it was clear as day from the back window, I want to buy that shit!

I'd put it on my dash so it didn't show my speedo though ;)

https://www.facebook.com/guardtrak

It was on the back window of the ute, not the back window of a sedan.

Clear as day at night, HD, GPS, google maps trackings, g force in all directions, knock detection recording etc.....

The business owners name is Rick, i know him through the Austech forum (jok11n).

http://www.austech.info/showthread.php?t=79469&page=4

Post # 66

Edit; you have the option not to show the speed on the recording in the options menu, i like it on, especially if caught for alleged speeding.

I sent him a PM there about this thread, he might chime in, if he reads this maybe he could do a group buy? Up to him.....

Edited by GTRPSI

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...