Jump to content
SAU Community

Recommended Posts

Hi guys have any one done a setup using NOS to spool a big turbo.

I was reading on google that this is possible but cant seem to get my head around how the system would work. From what i gather you would need a fuel/NOS injector. But would it be before or after the TB.??

I also read that you would need a pressure switch to turn it on and off like a pressure switch.

From what i gather it basically get rid of lag and can leave with full boost.

Im look for a diagram of the lay out. Does anyone have any links to how it would be done. ?????

Link to comment
https://www.sau.com.au/forums/topic/456398-big-turbo-using-nos-to-spool-it/
Share on other sites

Pretty sure it depends what NOS kit you have etc

Everyone I know running it on rb25's has it controlled by the ecu (mainly Vipec) to switch on at 2500 switch off at 4500 ish rpm when Vct kicks in yo for the exact reason you state to take away a bit of lag

No diagrams or anything from me though sorry

Edited by bcozican

I was reading around. Please look at the attached photo. But after reading it and looking a zex kit thats ment to do the same thing. The info i believe said on number 7 to place the fuel/NOS injector after the TB. I thought it would be before. Im drag racing a gtr. Rb26. With a gt42r. Would like to leave with 30psi. At around 9k. Its getting a bit clear in my head and may just buy this zex kit but the pressure switch look weak.

post-37293-1430880525637_thumb.jpg

post-37293-14308805545473_thumb.jpg

Looking to spool the turbo with trying to cause a fire. But i have heard of many ways that system works. Some guys bypass fresh air and duct it in the runners of the turbo manifold. But lots of guys in the states are doing this NOS METHOD to get boost off the line. From what i hear it works good. Nothing like the old bang bang methods. I just thought i would read up on it before i experience it first hand. I lile to understand how things work in my head before trying them. Check out this link of a supra using it.

I was reading around. Please look at the attached photo. But after reading it and looking a zex kit thats ment to do the same thing. The info i believe said on number 7 to place the fuel/NOS injector after the TB. I thought it would be before. Im drag racing a gtr. Rb26. With a gt42r. Would like to leave with 30psi. At around 9k. Its getting a bit clear in my head and may just buy this zex kit but the pressure switch look weak.

Have a look here, it's a RIPS install from NZ...single fogger just before the plenum:

http://www.gtr.co.uk/forum/75197-r-i-p-s-nitrous-install.html

snosinstall007cl7.jpg

This kind of depends on other aspects of the setup. Forgive me but is the car a GTR like your avatar picture? and will it be a manual trans?

Nos will help you get the turbo going when you're on the transbrake but if you're driving a manual 4WD then just set up launch control on your ecu with a clutch switch and full throttle launch it. Or am I missing something

Sadly i have a manual. But ive heard of guys having manual shift and still using nos to spool the turbo off the line. Using a boost switch to control the injection of nos. No thatd not the car im using in my profile photo. Its a r32 gtr

works killer best mod ever for big laggy turbos. even a 50hp shot can bring a big turbo on so much earlier.

Full throttle switch, arm switch and rpm switch are necessities, a decent ecu should have it there ready to go.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...