Jump to content
SAU Community

Recommended Posts

I got the rear end in yesterday, bled the clutch fitted the rear shaft and also replaced the nitrogen canister A4128799-E36E-4675-9A66-33530C812C27.thumb.jpeg.96a960982d9d9d850273d6b26b30845f.jpegnew and old next to each other

took the car for drive and the difference it amazing, was worth every cent. Now I just need an alignment before Friday 

1 hour ago, r32-25t said:

I got the rear end in yesterday, bled the clutch fitted the rear shaft and also replaced the nitrogen canister A4128799-E36E-4675-9A66-33530C812C27.thumb.jpeg.96a960982d9d9d850273d6b26b30845f.jpegnew and old next to each other

took the car for drive and the difference it amazing, was worth every cent. Now I just need an alignment before Friday 

Just out of interest (Doubtless has been asked) but how much for the canister?

  • Like 1

Because I hadn’t started the car for ages there was already no pressure in it. 

I had to buy a big socket go around it and remove the pressure switch to get the socket in there and then it was just unscrew the old one and fit the new one

Keeps the pressure in the pump, easiest way to know if yours is stuffed is while car car is sitting there idling you’ll hear the attessa pump cycle every couple of minutes. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...